Readytosky P23

Readytosky Mini 1000TVL FPV Camera User Manual

Model: P23

1. Introduction

This manual provides detailed instructions for the Readytosky Mini 1000TVL FPV Camera (Model P23). Designed for FPV drones, fixed-wing aircraft, and other DIY projects, this camera offers high-quality imaging and versatile compatibility. Please read this manual thoroughly before installation and operation to ensure optimal performance and safety.

2. Product Overview

The Readytosky Mini 1000TVL FPV Camera is a compact and lightweight imaging solution featuring a 1/3" High Sensitivity CCD image sensor. It provides a 1000TVL definition picture with good color quality and low illumination capabilities. The camera is switchable between NTSC and PAL video formats and operates on a wide voltage range of 5-20V.

2.1 Key Features

1000TVL definition for high-quality picture.
1/3" High Sensitivity CCD image sensor.
2.8mm wide-angle lens.
NTSC/PAL switchable video format.
Wide operating voltage: 5-20V.
Low power consumption.
Lightweight and high stability.

2.2 Product Components

Readytosky Mini 1000TVL FPV Camera with included cable — Figure 2.1: Readytosky Mini 1000TVL FPV Camera and connection cable.

Dimensions of the Readytosky Mini 1000TVL FPV Camera — Figure 2.2: Camera dimensions (e.g., 24.7mm length, 17.3mm width, 17.3mm height).

3. Setup

Proper setup is crucial for optimal performance. Follow these steps to connect your FPV camera.

3.1 Wiring Diagram

The camera comes with a standard 3-pin connector. Ensure correct polarity when connecting to your flight controller or video transmitter.

Red Wire: Positive Power Input (5-20V)
Black Wire: Ground (GND)
White Wire: Video Output (VID)

Readytosky Mini 1000TVL FPV Camera with its wiring harness — Figure 3.1: Camera with its wiring harness, showing the 3-pin connector.

3.2 NTSC/PAL Switching

The camera supports both NTSC and PAL video formats. A small switch on the back of the camera allows you to select the desired format. Ensure this matches the format supported by your FPV goggles or monitor.

Back of the Readytosky Mini 1000TVL FPV Camera showing the NTSC/PAL switch — Figure 3.2: Rear view of the camera, highlighting the NTSC/PAL selection switch.

4. Operating Instructions

Once properly installed and powered, the Readytosky Mini 1000TVL FPV Camera will output video signal directly. Connect the video output (white wire) to the video input of your FPV video transmitter or display device.

Power On: Apply 5-20V DC power to the camera.
Video Output: The camera will immediately begin transmitting video.
Lens Adjustment: The lens can be rotated to adjust focus if needed. Gently turn the outer ring of the lens until the image is clear.

5. Maintenance

To ensure the longevity and optimal performance of your FPV camera, follow these maintenance guidelines:

Cleaning: Use a soft, dry cloth to clean the camera body. For the lens, use a specialized lens cleaning cloth and solution to avoid scratches.
Storage: Store the camera in a dry, dust-free environment when not in use.
Handling: Avoid dropping the camera or subjecting it to strong impacts, as this can damage internal components or the lens.
Power Supply: Always ensure the input voltage is within the specified 5-20V range to prevent damage.

6. Troubleshooting

If you encounter issues with your Readytosky Mini 1000TVL FPV Camera, refer to the following common problems and solutions:

Problem	Possible Cause	Solution
No video signal / Black screen	Incorrect wiring, insufficient power, NTSC/PAL mismatch.	Check all wiring connections (power, ground, video). Verify input voltage is 5-20V. Ensure NTSC/PAL switch matches your display device.
Fuzzy or blurry image	Lens out of focus, dirty lens, damaged lens.	Gently rotate the lens to adjust focus. Clean the lens with a soft cloth. If damaged, consider lens replacement.
Image flickering or unstable	Power supply fluctuations, interference.	Ensure a stable power supply. Check for electromagnetic interference from other components.
Camera does not record to SD card	This camera model does not feature an integrated SD card slot for recording.	The Readytosky Mini 1000TVL FPV Camera is designed for live video output and does not support onboard recording via an SD card. External recording devices are required if recording functionality is desired.

7. Specifications

Feature	Detail
Brand	Readytosky
Model Number	P23
Video Capture Resolution	1000TVL
Photo Sensor Technology	1/3" CCD
Lens	2.8mm
Video Format	NTSC/PAL Switchable
Input Voltage	5-20V
Power Consumption	55mA @ 5V
Item Weight	0.81 ounces (approx. 23 grams)
Package Dimensions	4.29 x 2.2 x 0.83 inches
Special Features	Lightweight, Low Light Performance

8. What's in the Box

The standard package for the Readytosky Mini 1000TVL FPV Camera includes:

Camera Body
USB Cable

9. Warranty and Support

For warranty information or technical support, please contact Readytosky customer service through the platform where the product was purchased. Keep your purchase receipt as proof of purchase.

For more information, visit the official Readytosky Store.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.