Impression Obsession DIE645Y

Impression Obsession Faith Floral Steel Craft Die User Manual

Model: DIE645Y

Product Overview

The Impression Obsession Faith Floral Steel Craft Die (Model DIE645Y) is a precision-engineered steel die designed for scrapbooking and paper crafting. This single die features a detailed floral design incorporating the word "Faith". It is compatible with most table-top die cutting machines and is manufactured in the USA.

Impression Obsession Faith Floral Steel Craft Die, showing the intricate floral design with the word 'Faith' cut out.

Image: The Faith Floral Steel Craft Die, showcasing its intricate design with the word "Faith" centrally placed amidst floral and leafy patterns. This die is used for cutting shapes from paper or other thin materials.

Setup

To use the Faith Floral Steel Craft Die, you will need a compatible table-top die cutting machine. Ensure your machine is clean and in good working order before beginning. No assembly is required for the die itself.

Required Materials:

Impression Obsession Faith Floral Steel Craft Die (DIE645Y)
Compatible Die Cutting Machine (e.g., Cuttlebug, Sizzix Big Shot)
Paper or other material to be cut
Cutting plates appropriate for your machine
Optional: Metal adapter plate for detailed dies (recommended for Cuttlebug and other machines with very detailed dies)

Operating Instructions

Follow these steps to achieve optimal results when using your Faith Floral Steel Craft Die:

Prepare Your Sandwich: Refer to your die cutting machine's manual for the specific "sandwich" combination (arrangement of cutting plates, die, and material) required for thin metal dies. Generally, this involves a base plate, a cutting plate, your paper, the die (cutting edge down), and another cutting plate on top.
Position the Die: Place the Faith Floral die on your chosen material (e.g., cardstock) with the cutting edge facing down. Ensure the material covers the entire cutting area of the die.
Add Shims (If Necessary): For more detailed dies, additional shims (extra layers of cardstock or thin paper) may be required to increase pressure and ensure a clean cut. Place these shims under the bottom cutting plate or on top of the die, depending on your machine's recommendations.
Use a Metal Adapter Plate (Recommended for Detailed Cuts): If you are experiencing difficulty with intricate cuts, especially with machines like the Cuttlebug, a metal adapter plate can significantly improve results by providing more consistent pressure. Place the metal adapter plate as per your machine's instructions, typically replacing one of the standard cutting plates.
Run Through Machine: Carefully feed the assembled sandwich into your die cutting machine. Turn the crank or activate the machine according to its operating instructions.
Remove Cutout: Once the sandwich has passed through the machine, carefully remove the cutting plates and separate the die from your material. The cut design should now be visible.
Remove Excess Material: Use a die pick or similar tool to gently remove any small pieces of paper that may remain in the intricate areas of the die or the cut design.

Note: Different die cutting machines may yield varying results with detailed dies. Experiment with shims and pressure settings to find the optimal combination for your specific machine and material.

Maintenance

Proper maintenance will extend the life of your Faith Floral Steel Craft Die:

Cleaning: After each use, ensure all paper fibers and debris are removed from the die. A soft brush or die pick can be used for this purpose. Avoid using abrasive cleaners or solvents.
Storage: Store the die flat in a dry environment to prevent warping or rust. Magnetic storage sheets or dedicated die storage binders are recommended to keep the die secure and prevent loss.
Handling: Handle the die by its edges to avoid bending or damaging the intricate cutting areas. The die is made of steel, but excessive force or improper handling can cause deformation.

Troubleshooting

Problem	Possible Cause	Solution
Die does not cut completely through material.	Insufficient pressure from the die cutting machine; incorrect sandwich combination; worn cutting plates.	Add additional shims (cardstock or thin paper) to increase pressure. Ensure your sandwich combination matches your machine's recommendations for thin metal dies. Consider using a metal adapter plate for more consistent pressure. Replace worn or warped cutting plates.
Intricate details are not cutting cleanly.	Insufficient pressure; material too thick or fibrous; die is not sharp enough (unlikely for new steel dies).	Use a metal adapter plate. Add shims to increase pressure. Try a different type of paper or material that is less dense or fibrous. Run the die through the machine multiple times (forward and backward).
Die gets stuck in the material.	Material is too thick or too soft; excessive pressure.	Reduce shims if pressure is too high. Ensure material is suitable for die cutting. Gently pry the die and material apart using a thin, non-damaging tool.

Specifications

Model: DIE645Y
Product Name: Faith Floral Steel Craft Die
Brand: Impression Obsession
Material: Steel
Dimensions: 3-3/8 x 3-3/8 inches (approximately 8.57 cm x 8.57 cm)
Weight: Approximately 3 ounces (85 grams)
UPC: 848099034052
Manufacture Date: First available March 22, 2018
Origin: Made in USA

Warranty and Support

Impression Obsession products are manufactured to high standards. For specific warranty information or support regarding your Faith Floral Steel Craft Die, please contact Impression Obsession directly through their official website or authorized retailers. Keep your purchase receipt as proof of purchase.

For general inquiries or to find more information about Impression Obsession products, visit the official Impression Obsession website: www.impressionobsession.com