TuningPros DSVT2-708-2 Sunroof Moonroof Top Wind Deflector Visor User Manual

Product Overview

The TuningPros DSVT2-708-2 Sunroof/Moonroof Top Wind Deflector Visor is designed to reduce wind noise and keep rain out of your vehicle's sunroof. Constructed from high-quality acrylic in a dark smoke color, this Type 2 visor offers long-lasting durability and a sleek appearance. It features a direct tape-on design for easy installation without the need for cutting or drilling.

This deflector is specifically compatible with 2003-2009 Lexus GX470 models. Please ensure to measure your car's sunroof/moonroof and allow for approximately 1 inch (25.4mm) of space on each side for proper fitment, as the sunroof length is 1080mm (42.5 inches).

Specifications

Setup and Installation

The TuningPros Sunroof Wind Deflector is designed for a straightforward tape-on installation. No drilling or cutting is required.

1. 1. Prepare the Surface:

   Thoroughly clean the area on your vehicle's sunroof/moonroof where the deflector will be installed. Use an automotive-grade cleaner to remove any dirt, wax, or grease. Ensure the surface is completely dry before proceeding.

   

   Image: Close-up view of the deflector's pre-applied red adhesive tape on the underside, ready for installation.

2. 2. Test Fit the Deflector:

   Before removing the adhesive backing, carefully place the deflector on your sunroof to confirm the correct positioning and fit. Ensure it is centered and aligns properly with the sunroof opening. Remember to leave approximately 1 inch (25.4mm) of space on each side for optimal fitment.

   

   Image: Side profile view of the dark smoke sunroof deflector, showing its curved design.

3. 3. Apply the Deflector:

   Once you are satisfied with the positioning, peel off the protective film from the adhesive tape on the underside of the deflector. Carefully align the deflector with the marked position on your sunroof and press firmly along the entire length of the adhesive strips. Apply consistent pressure for several minutes to ensure a strong bond.

   

   Image: Underside view of the sunroof deflector, clearly showing the red adhesive tape strips along its edges.

4. 4. Secure the Installation:

   After applying, avoid washing your vehicle or exposing the deflector to heavy rain for at least 24-48 hours to allow the adhesive to fully cure. This will ensure maximum adhesion and durability.

   

   Image: The dark smoke sunroof deflector shown installed on the roof of a vehicle, viewed from the side.

Note: For best results, install the deflector in a warm, dry environment. If installing in cold weather, gently warm the adhesive tape with a hairdryer before application to improve adhesion.

Operating Instructions

Once installed, the TuningPros Sunroof Wind Deflector operates passively. It is designed to redirect airflow over your sunroof opening, reducing wind noise and preventing rain from entering the cabin when the sunroof is open. No active operation or adjustments are required from the user.

Image: Frontal view of the dark smoke sunroof deflector, showcasing its overall shape and design.

Maintenance

To ensure the longevity and appearance of your TuningPros Sunroof Wind Deflector, follow these simple maintenance guidelines:

• Clean the deflector regularly with mild soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the acrylic material.
• Use a soft cloth or sponge for cleaning to prevent scratching the surface.
• Rinse thoroughly with clean water and dry with a soft, lint-free cloth.
• Periodically inspect the adhesive bond to ensure it remains secure. If any lifting occurs, re-apply pressure or consider using a stronger automotive-grade adhesive if necessary (consult a professional if unsure).

Troubleshooting

Most issues related to the sunroof deflector are minor and can be resolved easily.

• Issue: Deflector is not adhering properly.

  Solution: Ensure the surface was thoroughly cleaned and dry before installation. The ambient temperature during installation should be above 50°F (10°C) for optimal adhesive performance. If installed in colder conditions, gently warm the adhesive with a hairdryer before application. Apply firm, consistent pressure for several minutes after placement.

• Issue: Increased wind noise after installation.

  Solution: Verify that the deflector is correctly positioned and securely attached. An improper fit or loose adhesion can sometimes cause unexpected airflow patterns. Ensure the sunroof is fully closed when not in use.

• Issue: Deflector appears scratched or dull.

  Solution: This can occur from using abrasive cleaning materials. Use only soft cloths and mild soap for cleaning. For minor scratches, specialized acrylic polish may be used, but always test on an inconspicuous area first.

Warranty and Support

TuningPros products are manufactured to high standards. For specific warranty information regarding your DSVT2-708-2 Sunroof Moonroof Top Wind Deflector Visor, please refer to the documentation included with your purchase or visit the official TuningPros website. Typically, products may be eligible for return or replacement within 30 days of purchase, subject to the seller's return policy.

For technical support, installation assistance, or warranty claims, please contact TuningPros customer service through their official channels. You can often find contact information on the product packaging or the seller's page on the platform where you made your purchase.

Manufacturer: TuningPros