Introduction
The AIM Solo 2 GPS Lap Timer is a highly precise and easy-to-use device designed for accurate lap time measurement. It utilizes data from two satellite constellations, GPS and Glonass, to ensure high precision, with lap times calculated within a maximum gap not higher than 2/100 of a second. The Solo 2 comes with an integrated database of over 2,000 tracks worldwide, allowing for automatic track recognition. Its configurable LED lights provide real-time feedback, enhancing the user's ability to improve performance.
Figure 1: The AIM Solo 2 GPS Lap Timer, showing its display and control buttons. This device is designed for precise lap time tracking.
Setup
Before using your AIM Solo 2, ensure it is properly set up and charged.
Charging the Device
- Connect the Solo 2 to a power source using the provided charging cable.
- A full charge typically provides up to 5 hours of battery life.
- Note: Some units may not indicate a full 100% charge, often showing around 90-93%. This is generally normal behavior and does not indicate a fault.
Mounting the Solo 2
- The back of the Solo 2 features a magnetic surface, allowing it to securely attach to compatible mounting plates.
- For additional security, especially in high-vibration environments, utilize the provided set screw or mounting hardware to firmly secure the device.
- Ensure the device is mounted in a location with a clear view of the sky for optimal GPS signal reception.
Initial Configuration and Track Database
- The Solo 2 comes with an integrated track database containing over 2,000 tracks worldwide.
- Upon powering on at a known track, the device should automatically recognize the location.
- For managing track data, updating firmware, or configuring advanced settings, connect the Solo 2 to a computer via Wi-Fi and use the official AIM software. Refer to the AIM Sports website for the latest software downloads and guides.
Operating Instructions
The AIM Solo 2 is designed for intuitive operation to provide immediate lap time feedback.
Powering On and Off
- To power on, press and hold the power button (usually located on the front panel).
- To power off, press and hold the power button until the device shuts down.
Lap Timing
- Once powered on and a GPS signal is acquired, the Solo 2 will automatically detect the track if it's in its database.
- Begin driving, and the device will automatically start recording lap times.
- Lap times are calculated with high precision, typically within 2/100 of a second.
Configurable LED Feedback
The Solo 2 features configurable RGB LEDs that provide real-time feedback on your performance. These LEDs can be customized to indicate whether your current pace is faster or slower than previous laps in specific sectors.
- Green Lights: Typically indicate a faster pace or improvement in a sector.
- Red Lights: Typically indicate a slower pace or a loss of time in a sector.
- The screen can be backlit in one of seven available colors for optimal visibility in various lighting conditions.
Figure 2: Solo 2 display with blue backlight.
Figure 3: Solo 2 display with green backlight.
Figure 4: Solo 2 display with red backlight.
Data Analysis
After a session, the Solo 2 can display session data, including fastest laps and sector times. For in-depth analysis, connect the device to your computer and use the dedicated AIM software to review and compare your performance data.
Maintenance
Proper maintenance ensures the longevity and optimal performance of your AIM Solo 2.
- Cleaning: Use a soft, dry cloth to clean the device. Avoid abrasive cleaners or solvents that could damage the screen or casing.
- Storage: Store the Solo 2 in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
- Battery Care: While the battery provides up to 5 hours of use, prolonged storage with a completely depleted battery can reduce its lifespan. Charge the device periodically even when not in active use.
- Software Updates: Regularly check the official AIM Sports website for software and firmware updates. Keeping your device updated can improve performance, add new features, and resolve potential issues.
Troubleshooting
If you encounter issues with your AIM Solo 2, refer to the following common problems and solutions:
| Problem | Possible Cause / Solution |
|---|---|
| No GPS Signal / Track Not Recognized |
|
| Session Ends Prematurely / Inaccurate Lap Times |
|
| Battery Not Charging to 100% |
|
| Difficulty with Software / Data Transfer |
|
Specifications
| Feature | Detail |
|---|---|
| Model Name | SOLO2 |
| Brand | AIM Sports |
| Connectivity Technology | Wi-Fi |
| Screen Size | 4.54 Inches |
| Item Weight | 1.7 pounds |
| Product Dimensions | 38.58 x 98 x 30 inches |
| Battery Life | Up to 5 Hours |
| Special Features | Integrated track database, Configurable RGB LEDs |
| Map Type | Worldwide (2,000+ tracks pre-loaded) |
| Included Components | AIM Solo 2 device, charging cable, mounting hardware (as supplied by manufacturer) |
Warranty and Support
For detailed information regarding the product warranty, technical support, and service, please refer to the official AIM Sports website or contact their customer service directly. Warranty terms and conditions may vary and are subject to the manufacturer's policies.
Official Website: www.aim-sportline.com
Note: This manual does not contain embedded video content as no official product videos from the seller were available in the provided data.