Product Overview
The Ekena Millwork Berkshire Thermoformed PVC Ceiling Medallion is designed to enhance the aesthetic appeal of your ceiling. Made from lightweight and durable thermoformed PVC, this medallion offers an easy installation process and can be finished to match your interior design. It is suitable for both interior and exterior applications.
Key Features:
- Lightweight, durable, and easy to install thermoformed PVC construction.
- Available in multiple sizes and finishes (this model is 22"OD, Unfinished).
- Low maintenance for long-lasting enjoyment.
- Suitable for both interior and exterior use.
- Designed to create a striking visual impact.
- Ready for painting or other finishes.
Installation Instructions
This section provides general guidelines for installing your Ekena Millwork Ceiling Medallion. Always ensure safety precautions are followed, including turning off power to any electrical fixtures before beginning work.
Tools and Materials Required:
- Adhesive (e.g., construction adhesive, caulk adhesive)
- Caulk gun (if using tube adhesive)
- Measuring tape
- Pencil
- Utility knife or scissors (for trimming if necessary)
- Safety glasses
- Ladder or sturdy step stool
Step-by-Step Installation:
- Prepare the Surface: Ensure the ceiling surface where the medallion will be installed is clean, dry, and free from dust or loose debris.
- Positioning: Carefully center the medallion around the existing light fixture canopy or desired location. Mark the position lightly with a pencil.
- Apply Adhesive: Apply a continuous bead of appropriate adhesive to the back of the medallion, particularly along the outer edge and any raised areas that will contact the ceiling. For a secure fit, also apply adhesive around the inner ring.
Image: Back view of the Ekena Millwork Berkshire Ceiling Medallion, illustrating recommended adhesive application points for secure installation. The image highlights areas for glue and caulk.
- Attach to Ceiling: Carefully lift the medallion and press it firmly against the marked position on the ceiling. Apply even pressure across the entire surface to ensure good adhesion.
- Secure and Caulk: If necessary, use small finishing nails or screws to temporarily hold the medallion in place until the adhesive cures. Apply a thin bead of caulk around the perimeter where the medallion meets the ceiling to seal any gaps and provide a finished look.
Image: A visual guide demonstrating the "Glue it. Stick it." installation method for the ceiling medallion, indicating where to apply glue and caulk for a seamless finish.
- Finishing (Optional): The medallion is unfinished and ready for paint. Once the adhesive and caulk are dry, you can paint the medallion to match or complement your ceiling or room decor.
Finishing and Customization
The Ekena Millwork Berkshire Ceiling Medallion comes unfinished, allowing for complete customization to suit your design preferences. It can be painted with most standard latex or oil-based paints.
Painting Tips:
- Clean the surface thoroughly before painting to ensure proper adhesion.
- Apply paint in thin, even coats to avoid drips and ensure a smooth finish.
- Consider using a primer for optimal paint adhesion and a more vibrant final color, especially if using a significantly different color than the base material.
- Allow each coat of paint to dry completely according to the paint manufacturer's instructions before applying subsequent coats.
Image: A display of over 30 color options, demonstrating the versatility of finishing for Ekena Millwork ceiling medallions. This model is unfinished, ready for your chosen paint.
Maintenance
The Ekena Millwork Berkshire Ceiling Medallion requires minimal maintenance. Once installed and finished, it can be cleaned with a soft, damp cloth to remove dust or light smudges. Avoid using abrasive cleaners or harsh chemicals, as these may damage the finish or the PVC material.
Troubleshooting
This section addresses common concerns that may arise during or after installation.
- Medallion does not sit flush with the ceiling:
Ensure the ceiling surface is even. If there are minor irregularities, apply a generous amount of adhesive and use painter's tape or temporary supports to hold the medallion firmly in place while the adhesive cures. Caulk any remaining gaps around the edge for a smooth transition.
- Adhesive not holding:
Verify that the correct type of adhesive for PVC and your ceiling material is being used. Ensure both surfaces are clean and dry. Allow sufficient curing time for the adhesive, which may vary based on product and environmental conditions.
- Warping of the medallion:
While thermoformed PVC is stable, extreme temperature fluctuations or improper storage before installation can cause slight warping. Ensure the medallion is stored flat in a climate-controlled environment. During installation, firm and even pressure with adequate adhesive application can help mitigate minor warping.
Specifications
| Attribute | Detail |
|---|---|
| Brand | Ekena Millwork |
| Model Number | CMP22BE |
| Style | Berkshire Medallion |
| Material | Thermoformed PVC |
| Outer Diameter (OD) | 22 inches |
| Inner Diameter (ID) | 3 1/2 inches (Fits canopies up to 10 1/8 inches) |
| Projection (P) | 1 inch |
| Finish | Unfinished (Paintable) |
| Item Weight | 4 ounces |
| Product Dimensions | 22 x 22 x 1 inches |
| Included Components | Ceiling Medallion (1) |
| Special Features | Lightweight |
Warranty and Support
Specific warranty information for the Ekena Millwork CMP22BE Berkshire Thermoformed PVC Ceiling Medallion is not provided in the product details. For warranty inquiries or technical support, please contact Ekena Millwork directly through their official website or customer service channels.
You can visit the Ekena Millwork Store on Amazon for more product information and contact options.
