Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your SAMDO Universal Motorcycle Speedometer Odometer Tachometer RPM Speedometer Gauge. This all-in-one unit is designed for carburetor motorcycles with a 12V DC power supply and is adjustable for various wheel sizes (8-22 inches). It integrates essential functions such as speed, odometer, trip distance, gear position, RPM, fuel level, and various indicator lights.
Figure 1: Front view of the SAMDO Universal Motorcycle Speedometer, displaying time, gear, speed, total distance, and fuel level.
Setup
Package Contents
- 1x SAMDO Speedometer Unit
- 1x Speed Sensor
- 2x Magnets
- 1x English User Manual & Wire Diagram
Figure 2: Included components: speedometer, speed sensor, and magnets.
Installation Steps
- Mounting the Speedometer: Securely mount the speedometer unit to your motorcycle's dashboard or desired location. Refer to the provided wire diagram for specific mounting points and connections.
- Speed Sensor Installation: Install the speed sensor and magnets. The speed sensor is a Hall effect type. Ensure the magnets are properly aligned with the sensor for accurate speed readings.
- Wiring Connections: Connect the wiring harness to your motorcycle's electrical system. The unit operates on DC 12V. Pay close attention to the wire diagram for correct connections of power, ground, indicators, fuel level, and RPM signals.
- RPM Cable Connection:
- For Single cylinder and 2 cylinder motors, the RPM cable connects to the trigger signal line positive pole.
- For 4 cylinder motors, the RPM cable connects to the ignition coil output line.
Note: The RPM function is not compatible with Electronic Fuel Injection (EFI) engines. If your motorcycle has an EFI engine, the RPM function will not work properly, though other functions will operate as intended.
- Initial Setup: After installation, power on the unit. You may need to adjust the wheel perimeter and pulse settings for accurate speed and distance measurements. Consult the detailed user manual for specific instructions on these adjustments.
Figure 3: Examples of the speedometer installed on different motorcycles.
Figure 4: Detail of the wiring connectors for installation.
Installation Video Guides
Video 1: Official SAMDO video demonstrating the motorcycle speedometer, odometer, and tachometer functions.
Video 2: Official SAMDO video showcasing the 199 Mph Motorcycle Speedometer in operation.
Operating Instructions
Key Functions
- Speed Display: Digital display of speed, range 0-199 km/h or mph.
- Distance Tracking: Digital display for trip distance (0-999.9 km/miles) and odometer distance (0-99999.9 km/miles).
- RPM Display: Needle display for RPM, range 0-13000.
- Fuel Level: LED display for fuel level with low fuel warning and blinking indicator.
- Indicators: LED shows left and right blinker, Neutral (N), high-beam, and water temperature.
- Clock: Displays current time.
Figure 5: The speedometer display showing a speed of 199 Kph.
Adjustments
- Unit Conversion: Easily shift between mph and km/h display modes.
- Trip Reset: Trip distance can be cleared as needed.
- Wheel Perimeter Adjustment: The unit allows for adjustable wheel perimeter settings to ensure accurate speed and distance readings across different vehicle types.
- Pulse Adjustment: The pulse setting is adjustable to match various engine types and ensure accurate RPM readings.
Maintenance
To ensure the longevity and optimal performance of your SAMDO Speedometer, follow these general maintenance guidelines:
- Cleaning: Use a soft, damp cloth to clean the display and casing. Avoid abrasive cleaners or solvents that could damage the screen or plastic.
- Connection Checks: Periodically inspect all wiring connections to ensure they are secure and free from corrosion. Loose connections can lead to intermittent functionality.
- Environmental Protection: While designed for motorcycle use, prolonged exposure to extreme weather conditions (heavy rain, direct sunlight, extreme temperatures) should be minimized to prevent potential damage.
- Sensor Care: Keep the speed sensor and magnets clean and free from debris to maintain accurate readings.
Troubleshooting
Common Issues and Solutions
- RPM Function Not Working: If your motorcycle has an Electronic Fuel Injection (EFI) engine, the RPM function of this speedometer is not compatible and will not work. This unit is designed for carburetor motors.
- Inaccurate Speed/Distance Readings: Ensure the wheel perimeter and pulse settings are correctly configured according to your motorcycle's specifications. Refer to the user manual for adjustment procedures. Verify that the speed sensor and magnets are properly installed and aligned.
- Display Issues (e.g., blank screen, flickering): Check all power and ground connections for security. Ensure the unit is receiving stable 12V DC power. If issues persist, consult the wire diagram for potential misconnections.
- Indicators Not Lighting Up: Verify the wiring for the specific indicator (e.g., turn signals, high-beam, neutral) is correctly connected as per the wire diagram. Check the corresponding bulbs or LEDs on your motorcycle.
For persistent issues not covered here, please refer to the detailed user manual or contact SAMDO customer support.
Specifications
| Feature | Detail |
|---|---|
| Item Height | 45 mm |
| Item Width | 90 mm |
| Item Length | 190 mm |
| Item Weight | 500 Grams |
| Working Temperature | -30 to 85°C |
| Working Voltage | 9-16V |
| Speed Range | 0-199 km/h or mph |
| Trip Distance Range | 0-999.9 km or miles |
| Odometer Distance Range | 0-99999.9 km or miles |
| RPM Range | 0-13000 r/min |
| Material | Polycarbonate (PC) |
| Screen Size | 90 Millimeters |
Figure 6: Detailed dimensions of the speedometer unit.
Warranty and Support
For warranty information, technical support, or any inquiries regarding your SAMDO Universal Motorcycle Speedometer, please refer to the contact details provided in the product packaging or visit the official SAMDO website. Keep your purchase receipt for warranty claims.