Introduction
This manual provides comprehensive instructions for the proper setup, operation, and maintenance of your VICS Wide Wall Swipe ID Card Badge Rack, Freedom Model 150. Please read this manual thoroughly before installation and use to ensure optimal performance and longevity of the product.
The VICS Freedom Model 150 is designed for organizing and displaying ID badges, particularly wide-format badges with lanyards or clips attached. It features a durable all-steel construction and is proudly made in the USA.
Product Features
- Designed for WIDE format ID badges.
- Accommodates badges with clips attached.
- Accommodates badges with lanyards attached.
- Constructed from durable all-steel material.
- Pocket Width: 4-9/16 inches.
- Card Exposure: 1-1/4 inches.
- Suggested Card Height: 2-1/8 inches or greater.
Setup and Installation
The VICS Freedom Model 150 is designed for wall mounting. Ensure the mounting surface is sturdy and capable of supporting the rack's weight, plus the weight of the badges it will hold.
Required Tools (Not Included):
- Drill
- Screwdriver (appropriate for mounting screws)
- Level
- Measuring Tape
- Pencil
- Mounting Screws and Wall Anchors (if necessary for your wall type)
Installation Steps:
- Select Location: Choose a suitable wall location that is easily accessible and provides sufficient space for the rack and badge insertion/removal.
- Mark Mounting Points: Hold the badge rack against the wall at the desired height. Use a level to ensure it is straight. Mark the positions of the mounting holes with a pencil.
- Drill Pilot Holes: Using an appropriate drill bit for your mounting screws and wall type, drill pilot holes at the marked locations. If using wall anchors, install them now according to their instructions.
- Mount the Rack: Align the badge rack with the pilot holes (or anchors). Insert and tighten the mounting screws until the rack is securely fastened to the wall. Do not overtighten.
- Verify Stability: Gently tug on the installed rack to ensure it is firmly attached and does not wobble.
Image: The VICS Freedom Model 150 ID Card Badge Rack in orange, showing its 25 slots for ID cards. This image illustrates the product's design and capacity.
Operating Instructions
Using the VICS Freedom Model 150 badge rack is straightforward.
- Insert Badges: Slide ID badges into the slots from the top. Ensure the badge is fully seated within the slot. The wide design accommodates badges with attached clips or lanyards.
- Remove Badges: Gently pull the desired ID badge upwards and out of its slot.
- Capacity: The rack features 25 individual slots. Avoid forcing more than one badge into a single slot to prevent damage to the rack or badges.
The 1-1/4 inch exposure allows for easy visibility and access to the top portion of the badge for quick identification.
Maintenance
The VICS Freedom Model 150 badge rack requires minimal maintenance due to its durable steel construction.
- Cleaning: Wipe the rack periodically with a soft, damp cloth to remove dust and dirt. Avoid abrasive cleaners or solvents, as these may damage the finish.
- Inspection: Periodically check the mounting screws to ensure they remain tight. Retighten if necessary.
- Damage: If the rack becomes bent or damaged, inspect it for sharp edges that could harm users or badges. Consider replacement if structural integrity is compromised.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Rack feels loose on the wall. | Mounting screws are loose or wall anchors are not secure. | Retighten mounting screws. If the problem persists, inspect wall anchors and replace if damaged or improperly installed. |
| Badges do not fit into slots. | Badge dimensions exceed slot specifications (4-9/16" width, 2-1/8" minimum height). | Verify badge dimensions. This rack is designed for wide badges; standard badges may fit loosely. Ensure no obstructions are in the slot. |
| Rack appears bent or damaged. | Physical impact or excessive force. | Inspect for sharp edges. If functionality or safety is compromised, consider replacing the unit. |
Specifications
| Model: | Freedom Model 150 |
| Brand: | VIC |
| Manufacturer: | VICS |
| Material: | Alloy Steel |
| Number of Slots: | 25 |
| Pocket Width: | 4-9/16 inches |
| Card Exposure: | 1-1/4 inches |
| Suggested Card Height: | 2-1/8 inches or greater |
| Item Weight: | 5.1 pounds |
| Manufacturer Part Number: | 150-0009 |
Warranty and Support
Specific warranty information for the VICS Freedom Model 150 is not provided in the product details. For warranty claims or technical support, please contact the manufacturer, VICS, directly through their official website or customer service channels.
When contacting support, please have your product model (Freedom Model 150) and manufacturer part number (150-0009) available.