Godox Xpro-C TTL Wireless Flash Trigger for Canon - Instruction Manual

Overview

The Godox Xpro-C TTL Wireless Flash Trigger is a versatile and powerful tool designed for Canon cameras, offering advanced control over your flash units. It supports TTL autoflash, high-speed sync, multi-flash, and manual flash modes, providing photographers with flexible lighting solutions. Its large LCD screen and intuitive button layout ensure ease of use, while features like TCM transform function and wireless ID settings enhance efficiency and reliability.

Key Features

• ONLY Compatible with Canon Cameras: There Is a Film on the Product Screen, If You See Small Traces Like Scratches on the Product Screen, It Is Normal to Exist.
• TTL Autoflash and Pro Functions: Support TTL Autoflash, 1/8000s High-Speed Sync, Multi Flash, Manual Flash, Flash Exposure Compensation, TCM Transform Function, Magnification Function, One-Shoot & Multi- Shoot Setting, Group Modeling Lamp Control, Group Zooming, Adjusting All Groups' Output Value Simultaneously, Etc
• SMART TCM BUTTON: Long Press TCM Button Can Transform the Flash Value in TTL Mode into the Power Output Value in M Mode; Short Press TCM Button Enables the Groups to Be Switched Between the One-Group and Multi-Group Mode
• Versatile Using Methods: As a Wireless Godox Flash Trigger/ Wireless Shutter Release Trigger/ Wireless Canon Speedlights Trigger/ Flash Trigger with 2.5mm Sync Cord Jack
• 01-99 WIRELESS ID: Only Achieve Triggering When the Channels and Wireless IDs of the Master and Slave Unit Are Set to the Same, Avoiding Signal Interference Effectively
• LARGE LCD Display: 16 Groups and 32 Channels to Wirelessly Control and Trigger. Full Graphic Display of 5 Groups Simultaneously.

Setup Guide

Battery Installation

The Godox Xpro-C requires two AA batteries for operation.

Locate the battery compartment on the underside of the unit. Insert two AA batteries, ensuring correct polarity as indicated inside the compartment.

Mounting to Camera

The Xpro-C features a hot shoe mount for secure attachment to your camera.

Slide the hot shoe of the Xpro-C into your camera's hot shoe slot until it clicks into place. Tighten the locking ring for a secure connection.

Operating Instructions

Powering On/Off

To power on the device, slide the "ON/OFF" switch located on the side of the unit. The large LCD screen will illuminate.

To power off, slide the switch back to the "OFF" position.

Basic Controls

The Xpro-C features an intuitive control layout:

• Group Buttons (A-E): Dedicated buttons on the left side allow quick selection and adjustment of individual flash groups.
• Function Buttons: Four buttons below the screen (CH/ZM, SYNC, ALL, MOD) provide access to channel, zoom, sync mode, and modeling light controls.
• SET Button & Dial: The central dial and SET button are used for navigating menus and adjusting values.
• MODE Button: Cycles through flash modes (TTL, Manual, Multi).
• TCM Button: Long press to convert TTL flash value to Manual power output; short press to switch between one-group and multi-group mode.

The image above illustrates the main control buttons and their placement on the unit.

Flash Modes

TTL Autoflash Mode

In TTL mode, the flash trigger automatically adjusts flash output for correct exposure. Use the MODE button to select TTL.

Manual Flash Mode

For precise control, switch to Manual mode using the MODE button. Adjust power output for each group using the dial and group buttons.

The image shows the difference in display between TTL and Manual modes, with Manual mode allowing direct power level adjustments.

Multi Flash Mode

This mode allows for stroboscopic flash, firing multiple flashes during a single exposure. Refer to the full user guide for detailed settings.

High-Speed Sync (HSS)

The Xpro-C supports 1/8000s High-Speed Sync, enabling you to use flash at shutter speeds faster than your camera's native sync speed. Activate HSS via the SYNC button.

Wireless ID Settings

To avoid signal interference, set the Wireless ID (01-99) on both the trigger and your flash units to the same value.

The menu option for setting the Wireless ID is shown above.

Versatile Usage Scenarios

The Godox Xpro-C can be used in various configurations to suit your photographic needs:

• Wireless Godox Flash Trigger: Control camera flashes, outdoor flashes, and studio flashes with built-in Godox wireless X system.
• Wireless Canon Speedlights Trigger: Use in combination with an X1R-C receiver to control original Canon speedlights.
• Wireless Shutter Release Trigger: Connect to your camera via a 2.5mm sync cord to remotely trigger the camera's shutter.
• Flash Trigger with 2.5mm Sync Cord Jack: Trigger flashes without the Godox X system using the sync cord.

This diagram illustrates the different ways the Xpro-C can be integrated into your lighting setup.

Maintenance

• Keep the unit dry. Do not handle with wet hands.
• Avoid extreme temperatures.
• Clean with a soft, dry cloth. Do not use solvents or harsh chemicals.
• Remove batteries if the unit will not be used for an extended period.
• Protect the hot shoe contacts from dust and damage.

Troubleshooting

Flash Not Firing

• Ensure batteries are correctly installed and charged.
• Verify the trigger and flash units are on the same channel and Wireless ID.
• Check that the trigger is securely mounted on the camera's hot shoe.
• Confirm the flash unit is powered on and set to receiver mode (if applicable).
• If using a 2.5mm sync cord, ensure it is properly connected to both the trigger and the flash/camera.

Screen Not Displaying

• Check battery level and replace if necessary.
• Ensure the power switch is in the "ON" position.

Inconsistent Flash Output

• Check for strong signal interference from other wireless devices. Adjust Wireless ID if needed.
• Ensure flash units are within the effective transmission range (0-100m).
• Verify flash mode settings (TTL/Manual) are appropriate for your shooting conditions.

Technical Specifications

Firmware Update

The Godox Xpro-C supports firmware upgrades via its Type-C USB port. This allows for future compatibility and feature enhancements.

Connect the trigger to a computer using a Type-C USB cable and follow the instructions provided on the official Godox website for the latest firmware and update procedure.

Warranty and Support

For detailed warranty information and customer support, please refer to the official Godox website or the documentation included with your product.

A digital version of the user guide is available here: User Guide (PDF).