Introduction
The Mytee S-300H Tempo Heated Extractor is a compact yet powerful machine designed for professional auto detailing, carpet, and upholstery spotting. Its sub-compact size and lightweight design (approximately 26 lbs) make it highly portable, while its robust features ensure effective cleaning. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your S-300H Tempo Heated Extractor.
Safety Information
Always observe basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, or injury. Read all instructions before using this machine.
- Ensure the power cord is in good condition and properly grounded. The lighted power cord indicator glows when power is present.
- Do not operate the machine with a damaged cord or plug.
- Keep water and moisture away from electrical components. The switches are water-resistant, but direct exposure to excessive water should be avoided.
- Do not immerse the machine in water.
- Use only recommended cleaning solutions.
- Unplug the machine from the power outlet before servicing or cleaning.
- Do not allow children to operate this machine.
- Operate on a level surface to prevent tipping.
- The heater element can reach high temperatures. Exercise caution when handling heated components or solution. The lighted switch indicates when the heater is active.
Components and Included Accessories
The Mytee S-300H Tempo Heated Extractor comes with the following components and accessories:
- Mytee S-300H Tempo Heated Extractor Unit
- 4" Air Lite Upholstery Tool (Part # 8400P)
- 8' Vacuum and Internal Solution Hose Combo
- Heatguard Hose Wrap (Part # A104)
- 25' Power Cord (Part # E617A)
Figure 1: The Mytee S-300H Tempo Heated Extractor shown with its 8-foot vacuum and internal solution hose combo, and the 4-inch Air Lite Upholstery Tool attached. This image illustrates the primary components ready for operation, highlighting the compact design of the main unit and the length of the hose for extended reach during cleaning tasks.
Setup
- Unpacking: Carefully remove the extractor and all accessories from the packaging. Inspect for any shipping damage.
- Positioning: Place the extractor on a stable, level surface near a grounded electrical outlet. The unit is equipped with wheels for easy transport.
- Fill Solution Tank: Unscrew the cap on the solution tank (the smaller tank, typically blue or light-colored) and fill with clean water and your preferred carpet/upholstery cleaning solution according to the solution manufacturer's instructions. Do not overfill. The tank capacity is approximately 1 gallon.
Figure 2: A close-up view of the solution tank cap on the Mytee S-300H Tempo Heated Extractor. This cap is located on the top of the unit, providing access to fill the tank with water and cleaning solution. Ensure the cap is securely tightened after filling to prevent leaks during operation.
- Connect Hoses: Connect the 8' vacuum and internal solution hose combo to the appropriate ports on the extractor. The vacuum hose connects to the larger port, and the solution hose connects to the brass quick-connect fitting. Ensure connections are secure.
- Attach Upholstery Tool: Connect the 4" Air Lite Upholstery Tool to the end of the hose combo.
- Power Connection: Plug the 25' power cord into a grounded electrical outlet. The lighted power cord indicator will illuminate, confirming power is supplied.
Operating Instructions
Follow these steps for effective cleaning with your Mytee S-300H Tempo Heated Extractor:
- Pre-test: Always pre-test your cleaning solution on an inconspicuous area of the material to be cleaned to ensure colorfastness and compatibility.
- Turn On Vacuum: Locate the vacuum switch on the control panel and turn it to the "ON" position. The vacuum motor will start, providing 85" of water lift for powerful extraction.
- Activate Heater (Optional): If heated cleaning is desired, turn the heater switch to the "ON" position. The lighted switch will indicate that the heater is active. Allow a few minutes for the water to heat up. The 600-watt heater provides powerful heating for enhanced cleaning.
- Apply Solution: Hold the upholstery tool firmly against the surface to be cleaned. Press the trigger on the tool to spray the cleaning solution onto the fabric.
- Extract: While spraying, slowly pull the tool across the surface, allowing the vacuum to extract the dirty solution. Overlap passes slightly to ensure thorough cleaning. For heavily soiled areas, multiple passes may be required.
- Rinse (Optional): After cleaning with solution, you may choose to rinse the area with clean water (without solution) to remove any residue.
- Monitor Recovery Tank: The dirty water will be collected in the recovery tank (the larger, typically black tank). Monitor the recovery tank level.
Figure 3: A close-up view of the recovery tank opening on the Mytee S-300H Tempo Heated Extractor. This opening is where the extracted dirty water is collected. It is important to regularly check and empty this tank to maintain optimal vacuum performance and prevent overflow.
- Empty Recovery Tank: When the recovery tank is full, turn off the vacuum and heater switches. Disconnect the vacuum hose and empty the dirty water. Reconnect the hose before resuming operation.
- Completion: Once cleaning is complete, turn off both the vacuum and heater switches. Unplug the power cord from the outlet.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your extractor.
- Empty and Rinse Tanks: After each use, empty both the solution and recovery tanks. Rinse them thoroughly with clean water to prevent residue buildup and odors.
- Clean Hoses and Tools: Rinse the vacuum hose, solution hose, and upholstery tool with clean water. Ensure no debris is lodged in the tool's spray jet or vacuum slot.
- Wipe Down Exterior: Wipe the exterior of the machine with a damp cloth.
- Check Power Cord: Periodically inspect the power cord for any signs of damage, fraying, or cuts.
- Storage: Store the extractor in a clean, dry place, away from extreme temperatures. Coil the power cord neatly and secure hoses and tools to prevent damage.
Troubleshooting
This section addresses common issues you might encounter with your S-300H Tempo Heated Extractor.
| Problem | Possible Cause | Solution |
|---|---|---|
| No power to the unit. | Power cord not plugged in; tripped circuit breaker; faulty outlet. | Ensure power cord is securely plugged into a grounded outlet. Check circuit breaker. Test outlet with another device. |
| Vacuum motor not working. | Vacuum switch off; recovery tank full; vacuum hose clogged or disconnected. | Turn on vacuum switch. Empty recovery tank. Check vacuum hose for clogs and ensure it is securely connected. |
| No spray from upholstery tool. | Solution tank empty; solution hose disconnected; spray jet clogged; pump issue. | Fill solution tank. Ensure solution hose is securely connected. Clean spray jet with a thin wire. If problem persists, contact support. |
| Heater not heating water. | Heater switch off; insufficient water in solution tank; heater element malfunction. | Turn on heater switch (lighted switch should illuminate). Ensure solution tank has sufficient water. If heater still does not work, contact support. |
| Reduced suction. | Recovery tank full; vacuum hose or tool clogged; seals not tight. | Empty recovery tank. Clear any clogs in hose or tool. Check all connections and seals for tightness. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | S-300H |
| Brand | Mytee Products |
| Heater Wattage | 600 watts |
| Vacuum Motor | Two-stage, producing 85" water lift |
| Solution Tank Capacity | Approximately 1 gallon |
| Product Dimensions (L x W x H) | 20"D x 17"W x 10"H (20 x 17 x 10 inches) |
| Item Weight | 26 Pounds |
| Color | Blue/Black |
| Features | Water Resistant Switches, Lighted Power Cords, Lighted Heater Switch, Roto-molded Housing, Transport Handle and Wheels |
Warranty and Support
For warranty information, technical support, or to purchase replacement parts, please contact Mytee Products directly. Refer to the official Mytee Products website or your purchase documentation for the most current contact details and warranty terms.
Mytee Products Contact Information:
- Website: www.mytee.com
- Customer Service: Refer to website for phone numbers and email.
When contacting support, please have your model number (S-300H) and purchase date available.