HAMKOT Dual PSU Cable Adapter 24-Pin Instruction Manual

Introduction

The HAMKOT Dual PSU Cable Adapter is designed to allow the connection of two power supply units (PSUs) to a single ATX motherboard. This solution is ideal for systems requiring additional power, such as those with multiple graphics cards for gaming or cryptocurrency mining, without needing to upgrade to a single, more expensive high-wattage PSU. This adapter ensures both power supplies activate simultaneously, providing stable and synchronized power delivery to your components.

Product Features

• Allows connection of an additional PSU to your ATX motherboard (supports both 24-pin and 20-pin configurations).
• Enables powering more graphics cards (GPUs) on an existing motherboard without component upgrades.
• Both connected power supplies will power up simultaneously with the motherboard.
• Constructed with high-quality 18AWG wire for reliable performance.
• Features one male 24-pin (20+4 pin) connector and two female 24-pin connectors.

Package Contents

• 1x HAMKOT Dual PSU Power Cable (11.8 inch / 30cm length)

Setup Instructions

Follow these steps to correctly install and connect your HAMKOT Dual PSU Cable Adapter:

1. Identify Motherboard Port: Locate the main 24-pin ATX power port on your computer's motherboard.
2. Connect Adapter to Motherboard: Plug the male 24-pin (20+4 pin) connector of the HAMKOT adapter into the motherboard's ATX power port. Ensure it is fully seated and secure.
3. Connect Primary PSU: Take the 24-pin ATX power cable from your primary power supply unit (PSU) and connect it to one of the female 24-pin connectors on the HAMKOT adapter.
4. Connect Secondary PSU: Take the 24-pin ATX power cable from your secondary power supply unit (PSU) and connect it to the other female 24-pin connector on the HAMKOT adapter.
5. Secure Connections: Double-check all connections to ensure they are firm and properly aligned.
6. Space Requirement: Ensure there is sufficient physical space within your computer case to accommodate both power supply units.

Operating Instructions

Once the HAMKOT Dual PSU Cable Adapter is correctly installed, both connected power supply units will power on and off simultaneously with your computer system. No additional manual intervention is required to synchronize the PSUs.

Important Notices:

• Power Supply Compatibility: Some power supply models may not support 'null startup' or simultaneous activation. Ensure your PSUs are compatible with this type of adapter.
• Maximum Input Power: The adapter supports a maximum combined input power of 2000W from both power supplies. Do not exceed this limit.

Maintenance

To ensure the longevity and reliable operation of your HAMKOT Dual PSU Cable Adapter, consider the following maintenance tips:

• Keep Clean: Periodically inspect the connectors for dust or debris. Use compressed air to gently clean them if necessary.
• Cable Management: Avoid sharp bends or excessive tension on the cables, which can damage the internal wiring.
• Environmental Conditions: Ensure your computer case has adequate airflow to prevent overheating of the power supplies and cables.

Troubleshooting

If you encounter issues with your HAMKOT Dual PSU Cable Adapter, refer to the following troubleshooting guide:

System Not Powering On:

• Check All Connections: Ensure the male 24-pin connector is fully seated in the motherboard and both female 24-pin connectors are securely attached to your PSUs.
• Verify PSU Power: Confirm that both primary and secondary power supply units are plugged into working power outlets and their power switches are in the 'ON' position.
• PSU Compatibility: Some older or specific PSU models may not synchronize correctly. If possible, test with different PSUs to rule out compatibility issues.

Loose Wires or Intermittent Power:

• Inspect Connectors: Carefully inspect the wiring at the base of each connector. If any wires appear loose or detached, discontinue use immediately to prevent damage to your components.
• Re-seat Connections: Gently unplug and re-plug all connections to ensure a firm contact. Avoid forcing connectors.

Specifications

Warranty and Support

The HAMKOT Dual PSU Cable Adapter comes with a 90-day warranty from the date of purchase.

For technical assistance, troubleshooting, or to make a warranty claim, please contact HAMKOT customer service through the retailer where the product was purchased. Please have your purchase details and product model number (B074DQJY8K) ready when contacting support.