Product Overview
The Everpure 804-001 SHURflo Mini Water Boost System is designed to increase water pressure and optimize water flow for various equipment. This compact system ensures consistent water delivery, making it ideal for applications requiring stable water pressure. It features a 21 oz. tank and operates at 60 psi (4.14 bar) with 115V AC power.
Image: The Everpure 804-001 SHURflo Mini Water Boost System, a compact unit designed to boost water pressure.
Important Safety Information
Read all instructions carefully before installation and operation. Failure to follow these instructions may result in property damage, injury, or death.
- Electrical Safety: Ensure the power supply matches the system's requirements (115V AC). Disconnect power before servicing.
- Water Pressure: Do not exceed the maximum operating pressure of 60 psi (4.14 bar).
- Installation: All plumbing and electrical connections must comply with local codes and regulations.
- Temperature: Do not install in locations where freezing temperatures may occur.
- Maintenance: Only qualified personnel should perform maintenance or repairs.
Package Contents
Verify that all components are present before beginning installation:
- SHURflo Mini Water Boost System (with 21 oz. tank)
- Power Cord (attached)
- Instruction Manual
Setup and Installation
Pre-Installation Checklist
- Ensure adequate space for installation and future maintenance.
- Verify that the incoming water supply pressure is within acceptable limits for the system.
- Confirm that a grounded 115V AC electrical outlet is available.
- Gather necessary tools: wrench, pipe sealant/Teflon tape, screwdriver.
Mounting the System
The system should be mounted vertically on a sturdy surface using appropriate fasteners. Ensure the unit is level and securely attached to prevent vibration and noise.
Plumbing Connections
- Identify the water inlet and outlet ports on the system.
- Apply pipe sealant or Teflon tape to all threaded connections.
- Connect the incoming water supply line to the system's inlet port.
- Connect the system's outlet port to the equipment requiring boosted water pressure.
- Ensure all connections are tight to prevent leaks.
Electrical Connections
- Ensure the system is properly plumbed and free of leaks before connecting power.
- Plug the system's power cord into a grounded 115V AC electrical outlet.
- The system will automatically begin to pressurize once power is supplied.
Initial Startup
- Slowly open the water supply valve to the system.
- Open a downstream faucet or valve to allow air to purge from the system.
- Once a steady stream of water flows, close the downstream faucet.
- Check all connections for leaks.
Operation
The SHURflo Mini Water Boost System operates automatically. When water is drawn from the system, the pressure switch detects a drop in pressure and activates the pump to maintain the desired output pressure. When water flow stops, the pump will shut off once the system reaches its set pressure.
- The system is designed for intermittent duty. Avoid continuous operation for extended periods without flow.
- The integrated tank helps to reduce pump cycling and maintain stable pressure.
Maintenance
Routine Checks
- Monthly: Inspect all plumbing connections for leaks.
- Quarterly: Check the system's mounting for security and ensure no excessive vibration.
- Annually: Verify the system's performance by checking output pressure.
Cleaning
Clean the exterior of the unit with a damp cloth. Do not use abrasive cleaners or solvents. Ensure no water enters the electrical components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| System does not turn on | No power supply Faulty electrical connection | Check power outlet and circuit breaker Ensure power cord is securely plugged in |
| Low or inconsistent water pressure | Insufficient incoming water supply Air in the system Clogged lines/filters (if applicable) | Verify adequate incoming water flow Purge air from the system (see Initial Startup) Inspect and clean/replace any pre-filters |
| System runs continuously | Leak in plumbing Constant water demand | Inspect all connections and plumbing for leaks Ensure all downstream faucets/valves are closed when not in use |
| Excessive noise/vibration | Loose mounting Air in the system | Tighten mounting fasteners Purge air from the system |
Specifications
| Feature | Detail |
|---|---|
| Model Number | 804-001 |
| Manufacturer | Everpure |
| Item Weight | 8 pounds |
| Product Dimensions (L x W x H) | 13 x 12.99 x 6 inches |
| Material | Stainless Steel |
| Power Source | Corded Electric |
| Voltage | 115V AC |
| Tank Capacity | 21 oz. |
| Maximum Pressure | 60 psi (4.14 bar) |
Warranty and Customer Support
This Everpure product is covered by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Everpure website. For technical assistance, troubleshooting beyond this manual, or to inquire about replacement parts, please contact Everpure customer support directly.
Everpure Customer Support: Refer to your product packaging or the official Everpure website for the most current contact information.