1. Introduction
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Pinty 4-12x50 EG Rifle Scope Set. This comprehensive set includes a 4-12x50 illuminated reticle rifle scope, a reflex sight, and a green dot laser sight, designed for use on 22mm Weaver/Picatinny rails.
Key Features:
- 4-12x50EG Rangefinder Illuminated Riflescope with adjustable magnification.
- Red/Green illuminated reticle with 5 brightness levels for the riflescope.
- Reflex sight with 4 reticle patterns and red/green illumination.
- Green dot laser sight for quick target acquisition.
- Constructed from aerospace aluminum alloy for durability.
- O-ring sealing and nitrogen filling ensure 100% water and fog-proof performance.
- Integrated Picatinny rail mount for easy attachment.
Figure 1: Overview of the Pinty 4-12x50 EG Rifle Scope Set with labeled components including 5-level red/green adjustment, dot sight scope, elevation adjustment, green laser, 4x-12x power ring, focus ring, built-in Picatinny rail mount, and built-in sunshade with multi-coated, waterproof, shock-proof, fog-proof features.
2. Package Contents
Verify that all items listed below are present in your package:
- 1x 4-12x50EG Rangefinder Illuminated Riflescope
- 1x 4 Reticle Red & Green Reflex Sight
- 1x Green Dot Laser Sight
- 2x Allen Wrenches (for rail mounting and sight adjustment)
- 1x Lens Cover
- 1x Cleaning Cloth
- 3x Manuals (specific to each component)
- Batteries (included)
Figure 2: Complete package contents of the Pinty 4-12x50 EG Rifle Scope Set.
3. Setup and Installation
3.1. Mounting the Riflescope
- Attach to Rail: Loosen the screws on the integrated Picatinny rail mount. Position the riflescope onto a 22mm Weaver/Picatinny rail on your firearm.
- Secure Mount: Slide the scope to your desired eye relief position. Ensure the scope is level and tighten the mounting screws firmly using the provided Allen wrench. Do not overtighten.
Figure 3: Integrated Picatinny Rail Mount for secure attachment.
3.2. Installing the Reflex Sight
- Battery Installation: Open the battery compartment on the reflex sight and insert the appropriate battery (typically a CR2032, check the specific manual for the reflex sight).
- Mounting: Attach the reflex sight to the top Picatinny rail integrated on the riflescope. Secure it by tightening the mounting screw with an Allen wrench.
Figure 4: Pinty Reflex Sight with its adjustment controls.
3.3. Installing the Green Dot Laser Sight
- Battery Installation: Unscrew the end cap of the laser sight and insert the battery (typically a CR123A, refer to the laser sight's specific manual).
- Mounting: Attach the green dot laser sight to one of the side Picatinny rails on the riflescope. Tighten the mounting screws securely.
Figure 5: Pinty Green Dot Laser Sight.
4. Operating Instructions
4.1. Riflescope Operation
- Magnification Adjustment: Rotate the 4x-12x Power Ring (refer to Figure 1) to adjust the magnification from 4x to 12x.
- Focus Adjustment: Rotate the Focus Ring (refer to Figure 1) to achieve a clear image of your target.
- Reticle Illumination: The riflescope features red and green illumination. Rotate the illumination knob (labeled "5 Levels Red / Green Adjustment" in Figure 1) to select the desired color and brightness level (5 levels for each color).
- Windage and Elevation Adjustment: Remove the protective caps from the windage (horizontal) and elevation (vertical) adjustment turrets. Use a coin or flathead screwdriver to make adjustments. Each click typically represents a specific change in point of impact (e.g., 1/4 MOA). Turn the turrets in the indicated direction to move the point of impact.
Figure 6: Riflescope adjustment turrets and magnification ring.
4.2. Reflex Sight Operation
- Power On/Off and Brightness: Use the control knob on the side of the reflex sight to turn it on/off and adjust the brightness of the reticle.
- Reticle Pattern Selection: The reflex sight offers 4 different reticle patterns. Use the reticle selector switch to cycle through the available patterns.
- Windage and Elevation Adjustment: Use the small adjustment screws on the side and top of the reflex sight to adjust the point of aim.
4.3. Green Dot Laser Sight Operation
- Activation: Press the button on the laser sight body to activate or deactivate the green laser.
- Windage and Elevation Adjustment: Use the small Allen wrenches to adjust the windage and elevation screws on the laser sight to align the laser dot with your point of impact.
4.4. Sighting In (Zeroing)
Sighting in is crucial for accuracy. It is recommended to perform this at a controlled shooting range. Start at a closer distance (e.g., 25 yards) and gradually move to longer distances (e.g., 100 yards) for fine-tuning.
- Secure Firearm: Mount your firearm securely in a vise or on a stable rest.
- Initial Shots: Fire a group of 3-5 shots at a target.
- Adjust Riflescope: Observe the point of impact relative to your aim point. Adjust the riflescope's windage and elevation turrets to move the reticle towards the center of your shot group. Repeat until satisfied.
- Adjust Reflex Sight/Laser: Once the riflescope is zeroed, adjust the reflex sight and laser sight to align with the riflescope's point of aim. This allows for quick transitions between aiming methods.
- Confirm Zero: Fire additional groups to confirm that all sights are accurately zeroed at your desired distance.
5. Care and Maintenance
- Cleaning Lenses: Use the provided cleaning cloth or a soft, lint-free cloth specifically designed for optics. Gently wipe the lens surfaces to remove dust and smudges. For stubborn marks, use a small amount of lens cleaning fluid. Avoid harsh chemicals or abrasive materials.
- Cleaning Body: Wipe the exterior of the scope, reflex sight, and laser sight with a soft, damp cloth. Dry thoroughly.
- Water and Fog Proofing: The riflescope is O-ring sealed and nitrogen-filled, making it waterproof and fog-proof. However, avoid submerging the unit in water for extended periods. If exposed to water, wipe dry immediately.
- Storage: Store the scope set in a cool, dry place, away from direct sunlight and extreme temperatures. Use the lens covers to protect the objective and ocular lenses when not in use. Remove batteries if storing for extended periods to prevent leakage.
- Inspection: Periodically check all mounting screws and adjustments to ensure they remain tight and secure.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Unclear Image in Riflescope | Improper focus or magnification setting. | Adjust the Focus Ring and Power Ring until the image is clear. Ensure proper eye relief. |
| Reticle Not Illuminating | Dead battery or incorrect battery installation. | Check battery orientation. Replace battery if necessary. Ensure illumination knob is turned on. |
| Laser Sight Not Activating | Dead battery, incorrect battery installation, or loose connection. | Check battery orientation. Replace battery. Ensure end cap is fully tightened. |
| Laser Sight Not Holding Zero | Mounting screws are loose or recoil is affecting alignment. | Ensure all mounting screws are securely tightened. Re-zero the laser sight. Note that some lasers may be more susceptible to recoil-induced shift. |
| Point of Impact Shift | Loose mounting, impact, or improper zeroing. | Check all mounting screws for tightness. Re-zero the scope set. Avoid dropping or impacting the unit. |
If you encounter issues not listed here or require further assistance, please contact Pinty customer support.
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | HRS0005G5 |
| Magnification (Riflescope) | 4x - 12x |
| Objective Lens Diameter | 50 mm |
| Reticle Type | Rangefinder (Riflescope), 4 Patterns (Reflex Sight) |
| Illumination | Red/Green with 5 brightness levels (Riflescope & Reflex Sight) |
| Laser Type | Green Dot Laser |
| Mounting System | Integrated 22mm Weaver/Picatinny Rail Mount |
| Material | Aerospace Aluminum Alloy |
| Water/Fog Proof | Yes (O-ring sealed, Nitrogen filled) |
| Product Dimensions | 32.3L x 6.6W x 32.3H Centimetres (approximate for main scope) |
| Item Weight | 748 g (1.65 lbs) |
| Batteries Included | Yes |
8. Warranty and Support
Pinty products are designed for reliability and performance. While specific warranty details are not provided in this manual, Pinty is committed to customer satisfaction. If you encounter any issues or require technical support, please contact Pinty customer service directly. Refer to the contact information provided with your product packaging or visit the official Pinty website for support options.
For general inquiries or to explore other Pinty products, you may visit the Pinty Store on Amazon.
