Samsung SWA-8500S Wireless Rear Speaker System Instruction Manual

1. Introduction

This manual provides essential information for the proper setup, operation, and maintenance of your Samsung SWA-8500S Wireless Rear Speaker System. This 2.0 channel speaker system is designed to enhance your audio experience by adding immersive surround sound to compatible Samsung Soundbars. Please read this manual thoroughly before using the product to ensure optimal performance and safety.

2. Safety Information

• Electrical Safety: Do not expose the unit to rain or moisture. Do not open the casing; refer all servicing to qualified personnel. Ensure the power cord is not pinched or walked on.
• Placement: Place the speakers and wireless receiver module on a stable, level surface or securely mount them to a wall. Avoid placing near heat sources, direct sunlight, or in areas with excessive dust or vibration.
• Ventilation: Ensure adequate ventilation around the wireless receiver module to prevent overheating. Do not block ventilation openings.
• Cleaning: Disconnect from power before cleaning. Use a soft, dry cloth. Do not use liquid cleaners or aerosol sprays.

3. Package Contents

Verify that all components are present in the box:

• Wireless Receiver Module (1)
• Rear Speakers (2)
• Speaker Cables (2)
• Power Cord for Wireless Receiver Module (1)
• Instruction Manual (this document)

4. Product Overview

The Samsung SWA-8500S system consists of a wireless receiver module and two compact rear speakers designed to integrate seamlessly with compatible Samsung Soundbars.

Figure 4.1: Overview of the Samsung SWA-8500S Wireless Rear Speaker System, showing the two compact speakers and the central wireless receiver module.

Figure 4.2: Close-up view of the wireless receiver module, featuring 'STANDBY' and 'LINK' indicators on the front panel.

Figure 4.3: A single Samsung SWA-8500S rear speaker, illustrating its compact dimensions of approximately 3"D x 3"W x 5.7"H.

5. Setup

5.1 Connecting the Speakers to the Wireless Receiver Module

1. Identify the left and right speakers.
2. Connect the speaker cables to the corresponding terminals on the back of each rear speaker and the wireless receiver module. Ensure correct polarity (red to red, black to black).
3. Position the rear speakers behind your listening area, typically to the left and right.

5.2 Wall Mounting (Optional)

The speakers are wall-mountable. Use appropriate screws and wall anchors (not included) suitable for your wall type. Ensure the mounting location can support the weight of the speakers securely.

5.3 Pairing with a Compatible Samsung Soundbar

The SWA-8500S system must be paired with a compatible Samsung Soundbar. Refer to your specific Soundbar's instruction manual for detailed pairing instructions, as the process may vary slightly between models.

General Pairing Steps:

1. Plug in the power cord to the wireless receiver module and connect it to an electrical outlet. The LINK LED indicator on the module will blink blue.
2. Turn off your Samsung Soundbar.
3. On your Soundbar's remote control, press and hold the Mute button (or VOL button on some older models) for approximately 5-6 seconds until the "ID SET" message appears on the Soundbar's display.
4. The LINK LED on the wireless receiver module should turn solid blue, indicating a successful connection.
5. If the LINK LED continues to blink, repeat the pairing process.

Compatible Soundbar Models: HW-Q70R, HW-Q60R, HW-R650, HW-R550, HW-R450, HW-N400, HW-N450, HW-N550, HW-N650, HW-M360, HW-M450, HW-M4500, HW-M550, HW-Q60T, HW-T650, HW-S60T, HW-T550, HW-T450, T60M.

6. Operation

Once paired, the SWA-8500S rear speakers operate in conjunction with your Samsung Soundbar. All sound adjustments, including volume and surround sound modes, are controlled via the Soundbar's remote control.

• Sound Mode: Ensure your Soundbar is set to a surround sound mode (e.g., 'Surround Sound' or 'DTS Virtual:X') to activate the rear speakers.
• Rear Level Adjustment: Use your Soundbar's remote to access sound settings and adjust the 'REAR LEVEL' to your preferred volume. This setting allows you to balance the rear speaker output with the front channels.

7. Troubleshooting

If you encounter issues with your SWA-8500S system, refer to the following common solutions:

• No Sound from Rear Speakers:
  • Check if the wireless receiver module's LINK LED is solid blue. If blinking, re-pair the system (refer to Section 5.3).
  • Ensure speaker cables are securely connected to both the speakers and the wireless receiver module, checking for correct polarity.
  • Verify that your Soundbar's sound mode is set to a surround sound option.
  • Check the 'REAR LEVEL' setting on your Soundbar; it might be set too low.
• Intermittent Sound or Distortion:
  • Ensure the wireless receiver module is not obstructed and is within close proximity to the Soundbar.
  • Check for potential interference from other wireless devices (e.g., Wi-Fi routers, cordless phones). Try moving the module or Soundbar slightly.
• Pairing Failure:
  • Confirm your Soundbar model is listed as compatible (refer to Section 5.3).
  • Ensure you are pressing the correct button on your Soundbar's remote for ID SET (often Mute, not VOL).
  • Unplug and replug the wireless receiver module, then retry the pairing process.

8. Specifications

9. Warranty and Support

For warranty information and technical support, please refer to the warranty card included with your product or visit the official Samsung website. You may also contact Samsung customer service for assistance with product registration, troubleshooting, and service requests.