Introduction and Overview
This user manual provides comprehensive instructions for the installation, operation, and maintenance of your Shoprider Scootie (TE-787NA) Battery Replacement Kit. This kit includes two (2) OR-12120F2 12V 12AH Sealed Lead Acid (SLA) batteries, designed to meet or exceed the original equipment manufacturer (OEM) specifications for your scooter. These batteries are fully charged upon arrival and ready for immediate installation.
Product Features:
- Includes two (2) OR-12120F2 - 12V 12AH SLA Batteries
- Dimensions Per Battery: 5.94"L x 3.86"W x 4.06"H
- Terminal Type: F2
- Approved for transport by air, DOT, IATA, FAA and CAB certified
Image: Two Origin Battery OR-12120F2 12V 12AH SLA batteries, as included in the replacement kit.
Installation Guide (Setup)
Before beginning the battery replacement process, ensure the scooter is turned off and disconnected from any power source. It is recommended to wear appropriate safety gear, such as gloves and eye protection.
Steps for Battery Replacement:
- Prepare Your Workspace: Gather necessary tools, which may include a screwdriver, wrench, and a battery terminal cleaner. Ensure you have adequate lighting.
- Locate Battery Compartment: Refer to your Shoprider Scootie (TE-787NA) scooter's original manual to locate and access the battery compartment. This is typically under the seat or floorboard.
- Disconnect Old Batteries: Carefully disconnect the negative (-) terminal first, followed by the positive (+) terminal from the old batteries. Note the wiring configuration (series or parallel) for correct re-connection.
- Remove Old Batteries: Lift out the old batteries from the compartment. Be mindful of their weight.
- Inspect and Clean: Before installing new batteries, inspect the battery compartment for any debris or corrosion. Clean terminals and connectors if necessary.
- Insert New Batteries: Place the new OR-12120F2 batteries into the compartment, ensuring they are oriented correctly according to the original setup.
- Connect New Batteries: Connect the positive (+) terminal first, then the negative (-) terminal. Ensure all connections are secure and tight. Double-check your wiring against the original configuration.
- Secure Compartment: Close and secure the battery compartment.
- Initial Test: Turn on your scooter to confirm proper power. It is recommended to fully charge the new batteries before the first extended use, although they arrive pre-charged.
Image: Close-up of an F2 battery terminal, illustrating the connection point. Ensure secure connections during installation.
Operation and Charging
Your new batteries arrive fully charged and ready for use. For optimal performance and longevity, follow these guidelines:
- Initial Charge: While pre-charged, it is good practice to connect the scooter to its charger for a full charge cycle (typically 8-12 hours) before the first extended use.
- Regular Charging: Always charge the batteries after each significant use, even if only for a short period. Avoid completely discharging the batteries, as this can reduce their lifespan.
- Use Approved Charger: Always use the charger specifically designed for your Shoprider Scootie (TE-787NA) scooter. Using an incompatible charger can damage the batteries.
- Charging Environment: Charge batteries in a well-ventilated area, away from direct sunlight or extreme temperatures.
- Avoid Overcharging: Modern chargers typically have overcharge protection, but it's best to disconnect the charger once the charging cycle is complete.
Maintenance and Storage
Proper maintenance and storage will extend the life of your SLA batteries:
- Keep Terminals Clean: Periodically inspect battery terminals for corrosion. If corrosion is present, clean with a wire brush and a mixture of baking soda and water. Ensure terminals are dry before re-connecting.
- Regular Charging During Storage: If the scooter will not be used for an extended period (more than one month), charge the batteries fully and then recharge them every 4-6 weeks to prevent self-discharge and maintain capacity.
- Storage Environment: Store the scooter and batteries in a cool, dry place, ideally between 50°F and 70°F (10°C and 21°C). Avoid extreme hot or cold temperatures.
- Avoid Deep Discharges: As mentioned, consistently running the batteries until they are completely drained will significantly shorten their lifespan.
Troubleshooting Common Issues
This section addresses common issues you might encounter with your new batteries.
| Issue | Possible Cause | Solution |
|---|---|---|
| Scooter not powering on after battery replacement. | Loose or incorrect battery connections. | Check all battery terminal connections to ensure they are tight and correctly wired (positive to positive, negative to negative, and series/parallel as per scooter's original setup). |
| Batteries not holding a charge or short run time. | Incomplete initial charge, charger malfunction, or prolonged deep discharge. | Ensure batteries are fully charged. Test the charger to confirm it is functioning correctly. Avoid deep discharges. If issues persist, consult the scooter's main manual or a qualified technician. |
| Corrosion on battery terminals. | Exposure to moisture or chemical reactions. | Disconnect batteries. Clean terminals with a wire brush and a baking soda/water solution. Rinse with clean water and dry thoroughly before re-connecting. Apply anti-corrosion grease. |
Product Specifications
- Battery Type: Sealed Lead Acid (SLA)
- Voltage: 12 Volts (per battery)
- Capacity: 12 Amp Hours (AH) (per battery)
- Quantity: 2 batteries per kit
- Dimensions Per Battery (L x W x H): 5.94" x 3.86" x 4.06"
- Terminal Type: F2
- Recommended Use: Wheelchair / Mobility Scooter
- Certifications: Approved for transport by air (DOT, IATA, FAA, CAB certified)
- Manufacturer: Origin Battery
Warranty and Support
This Shoprider Scootie (TE-787NA) Battery Replacement Kit comes with a one-year warranty from the date of purchase. This warranty covers manufacturing defects and ensures the batteries meet their stated specifications under normal use.
For warranty claims, technical support, or any questions regarding your Origin Battery product, please refer to the contact information provided by your retailer or visit the official Origin Battery website for support resources. Please have your purchase receipt and product model information ready when contacting support.