Introduction
Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.
Safety Information
WARNING: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.
- Ensure power is OFF at the circuit breaker before installation.
- This device is intended for installation in accordance with the National Electric Code and local regulations.
- Do not use in wet locations or where directly exposed to water.
- For indoor use only.
Package Contents
- GoControl WS15Z5-1 Z-Wave Wall Switch
- Installation Screws
- Wire Nuts (may vary by package)
- User Manual (this document)
Setup and Installation
Follow these steps carefully to install your GoControl Z-Wave Wall Switch.
1. Wiring the Switch
- Turn OFF Power: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
- Remove Old Switch: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
- Identify Wires:
- Line (Hot): Usually black, coming from the circuit breaker.
- Load: Usually black, going to the light fixture or appliance.
- Neutral: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
- Ground: Usually green or bare copper.
- Connect New Switch: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
- Connect the Line wire to the terminal marked "LINE".
- Connect the Load wire to the terminal marked "LOAD".
- Connect the Neutral wire to the terminal marked "NEUTRAL".
- Connect the Ground wire to the terminal marked "GROUND".
Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.
- Mount Switch: Carefully push the wired switch into the wall box. Secure it with the provided screws.
- Install Wall Plate: Attach the new or existing wall plate.
- Restore Power: Turn the power back ON at the circuit breaker.
Figure 1: Front view of the GoControl WS15Z5-1 Z-Wave Wall Switch.
2. Z-Wave Inclusion (Pairing)
To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.
- Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
- On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle once. The LED indicator on the switch will blink to confirm inclusion mode.
- The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
- If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.
Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.
Operating the Switch
Manual Control
- Press the top of the paddle to turn the connected load ON.
- Press the bottom of the paddle to turn the connected load OFF.
Z-Wave Control
Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.
- Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
- The switch supports standard Z-Wave commands for basic on/off functionality.
Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.
Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.
Maintenance
The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.
- Cleaning: To clean the switch, wipe it with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Firmware Updates: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
- General Care: Ensure the switch is not exposed to excessive moisture or extreme temperatures.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Switch does not respond to manual press. | No power to the switch; incorrect wiring; faulty switch. | Check circuit breaker. Verify wiring connections (Line, Load, Neutral, Ground). If issues persist, contact support. |
| Switch does not respond to Z-Wave commands. | Not properly included in Z-Wave network; out of range; network interference. | Perform Z-Wave exclusion, then re-inclusion. Move controller closer to the switch during inclusion. Check for other Z-Wave devices interfering. |
| Cannot include switch into Z-Wave network. | Switch is already included in another network; controller not in inclusion mode. | Perform Z-Wave exclusion first (see below). Ensure your controller is in inclusion mode. |
| LED indicator is not behaving as expected. | Indicates network status or error. | Refer to your Z-Wave controller's manual for specific LED behavior interpretations or contact GoControl support. |
Z-Wave Exclusion (Removing from Network)
If you need to remove the switch from your Z-Wave network, follow these steps:
- Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
- On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle once. The LED indicator will blink to confirm exclusion mode.
- The controller will confirm successful exclusion. The switch's LED will stop blinking.
Specifications
| Model Number | WS15Z5-1 (RA45130) |
| Brand | GoControl |
| Operation Mode | ON-OFF |
| Connectivity Protocol | Z-Wave |
| Mounting Type | Wall Mount |
| International Protection Rating | IP54 |
| Item Dimensions (L x W x H) | 25 x 25 x 25 Millimeters (approx. 1 x 1 x 1 Inches) |
| Item Weight | 91 g |
| Batteries Included? | No |
Warranty and Support
GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl website or contact their customer service department.
Website: www.gocontrol.com
Manufacturer: GOCONTROL
