Dyna-Glo WK95C8B Kerosene Convection Heater User Manual

1. Introduction

This manual provides essential instructions for the safe and efficient operation, maintenance, and troubleshooting of your Dyna-Glo WK95C8B Indoor Kerosene Convection Heater. Please read this manual thoroughly before initial use and retain it for future reference.

The Dyna-Glo WK95C8B is designed to provide 360 degrees of convection heat, suitable for heating areas up to 1,000 square feet. It operates with 99% efficiency, making it an economical choice for supplemental heating.

2. Important Safety Information

• Ventilation: Always ensure adequate ventilation when operating the heater. Kerosene heaters consume oxygen and produce carbon monoxide. Use in well-ventilated areas only.
• Fuel Type: Use only 1-K grade kerosene. Never use gasoline, diesel, or other flammable liquids, as this can cause fire or explosion.
• Placement: Place the heater on a level, non-combustible surface. Maintain clear distances from walls, furniture, and other combustible materials as specified in the full safety guidelines.
• Tip-Over Safety Switch: This heater is equipped with a built-in safety switch that automatically shuts off the unit if it is accidentally knocked over.
• Children and Pets: Keep children and pets away from the operating heater.
• Never Leave Unattended: Do not leave the heater operating unattended.

3. Package Contents

Upon unpacking, verify that all items are present:

• Dyna-Glo WK95C8B Kerosene Convection Heater
• Wick (pre-installed)
• Additional Wicks (3 included)
• Fuel Siphon Pump
• Fuel Funnel
• Instruction Manual

4. Specifications

5. Setup

5.1 Unpacking and Inspection

Carefully remove the heater from its packaging. Inspect for any damage. Ensure all components listed in the "Package Contents" section are present.

5.2 Fueling the Heater

Always fill the heater outdoors or in a well-ventilated area to avoid inhaling fumes. Ensure the heater is cool before fueling.

1. Unscrew the fuel tank cap.
2. Insert the provided funnel into the fuel opening.
3. Use the siphon pump to transfer 1-K grade kerosene from your fuel container into the heater's tank. Fill the tank over half full, but do not overfill. The fuel gauge will indicate the level.
4. Securely replace the fuel tank cap.
5. For first use, allow the wick to absorb the kerosene for at least 30 minutes before attempting to ignite. This ensures proper saturation and prevents damage to the wick.

Figure 1: Dyna-Glo WK95C8B Kerosene Convection Heater. This image shows the overall design of the heater, highlighting its protective cage and fuel gauge.

6. Operating Instructions

6.1 Ignition

1. Ensure the wick is fully saturated with kerosene (after 30 minutes for first use).
2. Rotate the adjustment knob clockwise until the wick is fully raised and stops.
3. Press the ignition button or use a lighter/match to ignite the wick directly.
4. Once the wick is lit, quickly cover it with the burner cylinder and allow the flame to stabilize.

6.2 Flame Adjustment

After the heater is fully burning, adjust the knob to achieve an optimal flame. A proper flame should be steady and blue at the base, with a yellow tip, without excessive smoke or odor. Avoid flames that are too high or too low.

6.3 Cooking Function (Optional)

The top surface of the heater can be used as a cooktop. Place a stove riser stand (if included or purchased separately) on top of the heater to efficiently heat and keep kettles or pots warm. Ensure the pot or kettle is stable and does not obstruct airflow.

6.4 Extinguishing the Heater

1. To extinguish the flame, turn the adjustment knob counterclockwise all the way down.
2. For emergency shut-off, press the emergency fire extinguisher switch (if available on your model) to quickly lower the wick and extinguish the flame.

7. Maintenance

• Regular Cleaning: Keep the heater clean from dust and debris. Use a soft, dry cloth for exterior cleaning.
• Wick Maintenance: Periodically inspect the wick for wear or charring. A properly maintained wick ensures efficient burning and reduces odor. Refer to the full manual for detailed wick replacement instructions.
• Fuel Storage: Store kerosene in a clean, approved container in a cool, dry place away from direct sunlight and heat sources.

8. Troubleshooting

9. Warranty and Support

For warranty information, technical support, or to order replacement parts, please refer to the contact details provided in your product packaging or visit the official Dyna-Glo website. Keep your purchase receipt as proof of purchase.