Introduction
The Gator Frameworks GFW-UTL-MEDIATRAY1 is a versatile adjustable multi-media gear stand designed to securely hold various equipment such as laptops, projectors, small production samplers, and monitors. Its robust construction and adjustable features provide a stable and adaptable platform for your media needs.
This manual provides essential information for the safe and efficient setup, operation, and maintenance of your GFW-UTL-MEDIATRAY1 stand. Please read it thoroughly before assembly and use.
Safety Information
- Weight Capacity: Do not exceed the maximum load capacity of 9 kg (20 lbs). Overloading can cause instability and damage to the stand or equipment.
- Stable Surface: Always place the stand on a flat, stable, and level surface to prevent tipping.
- Leg Extension: Ensure all tripod legs are fully extended and locked into position before placing any equipment on the tray.
- Secure Equipment: Always use the provided adhesive EVA rubber pads to prevent equipment from sliding on the tray. For VESA-mounted monitors, ensure all mounting screws are securely tightened.
- Adjustments: Exercise caution when adjusting the height or angle of the stand, especially with equipment in place. Ensure all locking mechanisms are fully engaged after adjustment.
- Children and Pets: Keep children and pets away from the stand during assembly and operation to prevent accidents.
- Inspection: Regularly inspect the stand for any signs of wear, damage, or loose components. Do not use the stand if it is damaged.
Package Contents
Please verify that all components are present and undamaged upon opening the package. If any parts are missing or damaged, contact Gator Frameworks customer support immediately.
- Adjustable Tripod Base with Main Pole
- Reversible 1.2mm Steel Tray
- Adhesive EVA Rubber Pads (pre-cut strips)
- VESA 100x100 Mounting Brackets and Hardware (screws, washers, wing nuts)
- Safety Pin
Setup Instructions
- Unfold the Tripod Base: Place the tripod base on a flat surface. Extend the legs fully until they lock into their open position. Ensure the red rings on the rubber grip feet are visible and the base is stable.
- Insert Main Pole: Loosen the height adjustment knob on the tripod base. Insert the main pole into the top of the tripod base. Adjust to your desired height and secure by tightening the knob. For added security, insert the safety pin through the designated hole in the main pole and tripod base.
- Attach the Tray: The stand features a reversible tray. Determine which side you wish to use:
- Flanged Side Up: For laptops, samplers, or other equipment that benefits from a raised edge to prevent sliding.
- Flat Side Up: For VESA-mounted monitors or when a completely flat surface is preferred.
Align the tray's mounting bracket with the top of the main pole. Secure the tray using the provided hardware (e.g., wing nuts) to achieve the desired tilt angle. Ensure all connections are tight.
Image: Close-up of the VESA mounting bracket on the stand's pole, illustrating the attachment point for the tray and its tilt mechanism.
- Apply EVA Rubber Pads: If using the flanged side up for non-VESA equipment, apply the adhesive EVA rubber pads to the tray surface. These pads provide grip and prevent your equipment from scratching or sliding.
- VESA Mount Installation (Optional): If mounting a monitor, ensure the flat side of the tray is facing up. Attach the VESA 100x100 mounting brackets to the monitor using the appropriate screws. Then, secure the monitor with the attached brackets to the stand's tray using the provided hardware.
Operating Instructions
Once assembled, the Gator Frameworks Multi-Media Gear Stand offers flexibility for various applications.
- Height Adjustment: To adjust the stand's height, loosen the height adjustment knob on the main pole. Carefully raise or lower the pole to the desired height (between 28" and 44.5" / 711.2mm – 1130.3mm). Re-insert the safety pin into the nearest hole and tighten the knob securely.
- Tray Angle Adjustment: Loosen the wing nuts or knobs securing the tray to the main pole. Adjust the tray to your preferred angle, then tighten the fasteners firmly to lock it in place.
- Equipment Placement: Place your laptop, projector, sampler, or monitor onto the tray. Ensure it is centered and stable. The EVA pads will help prevent movement.
- Collapsing for Storage/Transport: To collapse the stand, remove any equipment from the tray. Loosen the tray fasteners and remove the tray. Loosen the main pole height adjustment knob, remove the safety pin, and lower the pole completely. Fold the tripod legs inward until they are compact.
Image: A laptop positioned on the adjustable, reversible steel utility tray, highlighting the adhesive EVA rubber pads for secure placement.
Image: A monitor securely attached to the stand, demonstrating the use of the 100x100 VESA mounting brackets.
Image: The stand shown in its fully collapsed configuration, illustrating its compact design for convenient transport and storage.
Maintenance
- Cleaning: Wipe down the stand with a soft, dry cloth. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying. Avoid abrasive cleaners or solvents.
- Hardware Check: Periodically check all screws, knobs, and fasteners to ensure they are tight. Loose hardware can compromise the stand's stability.
- Storage: Store the stand in a dry environment, away from extreme temperatures and humidity, to prevent corrosion.
Troubleshooting
- Stand is unstable or wobbly:
- Ensure the tripod legs are fully extended and locked.
- Verify that the stand is placed on a flat, level surface.
- Check that the height adjustment knob and tray fasteners are securely tightened.
- Confirm the safety pin is inserted correctly.
- Equipment slides on the tray:
- Ensure the adhesive EVA rubber pads are properly applied to the tray surface.
- Verify the tray is level or slightly tilted backward if using the flanged side up.
- Difficulty adjusting height or angle:
- Loosen the respective adjustment knobs or fasteners sufficiently before attempting to move components.
- Do not force adjustments; if resistance is met, re-check for obstructions or fully loosen fasteners.
- Missing or damaged parts upon arrival:
- Inspect all components immediately after unboxing.
- Contact Gator Frameworks customer support with your purchase details for assistance.
Specifications
| Model Number | GFW-UTL-MEDIATRAY1 |
| Material | Alloy Steel |
| Finish Type | Painted (Black) |
| Base Type | Tripod Leg |
| Load Capacity | 9 kg (20 lbs) |
| Adjustable Height | 28" to 44.5" (711.2mm – 1130.3mm) |
| Tray Dimensions (L x W) | 19.25" x 15.75" (489mm x 400mm) |
| VESA Compatibility | 100x100 |
| Item Weight | 9.2 pounds |
| Product Dimensions (Packaged) | 19.5 x 34 x 5 inches |
Image: A diagram illustrating the key dimensions of the stand, including tray length and width, and the adjustable height range.
Warranty and Support
For warranty information, technical support, or to inquire about replacement parts, please contact Gator Frameworks customer service directly. Refer to the official Gator Frameworks website or your purchase documentation for current contact details and warranty terms.
Manufacturer: Gator Cases
