1. Introduction
Thank you for choosing the SUPTEMPO Toilet Night Light. This device is designed to provide a convenient and colorful illumination for your toilet bowl, activating automatically in the dark when motion is detected. It features an 8-color changing LED system to enhance visibility and safety during nighttime use.
2. Safety Information
- This product is intended for indoor use only.
- Do not immerse the device in water or expose it to excessive moisture.
- Keep out of reach of children.
- Use only AAA batteries as specified. Do not mix old and new batteries or different types of batteries.
- Remove batteries if the device will not be used for an extended period.
3. Package Contents
- 1 x SUPTEMPO Toilet Night Light Unit
4. Product Overview
The SUPTEMPO Toilet Night Light is a compact, motion-activated LED light designed for toilet bowls. It features a flexible arm for easy attachment and a built-in motion sensor that detects movement in low-light conditions, illuminating the toilet bowl with a choice of 8 colors.
Image 4.1: Front view of the SUPTEMPO Toilet Night Light, highlighting its motion-activated feature and long battery life.
Image 4.2: Exploded view showing the LED light, motion sensor, color selection button, and 3*AAA battery compartment.
5. Setup and Installation
- Install Batteries: Open the battery compartment cover on the back of the unit. Insert 3 AAA batteries, ensuring correct polarity (+/-). Close the cover securely.
- Attach to Toilet: Bend the flexible arm to fit over the rim of your toilet bowl. Position the main unit on the outside of the toilet and the LED light arm inside the bowl. Ensure the motion sensor on the front of the unit faces outwards, towards where a user would approach.
- Secure Placement: Adjust the flexible arm to ensure the unit is stable and the LED light is positioned to illuminate the inside of the bowl effectively.
Image 5.1: The night light unit securely attached to the side of a toilet bowl, with the flexible arm extending into the bowl.
6. Operating Instructions
- Automatic Activation: The toilet night light is equipped with a motion sensor and a light sensor. It will only activate in dark conditions when motion is detected within its range.
- Color Cycling Mode: Upon activation, the light will automatically cycle through its 8 different colors. Each color will display for approximately 15 seconds before transitioning to the next.
- Single Color Mode: To select a single color, press the small button located on the side of the main unit (refer to Image 4.2). Each press will advance to the next color in the sequence. Once your desired color is displayed, stop pressing the button. The light will remain in this single color mode until the batteries are removed or replaced, or the button is pressed again to resume cycling.
- Deactivation: The light will automatically turn off approximately 2 minutes after the last detected motion, provided there is no further movement and the ambient light level is sufficient.
Image 6.1: A side-by-side comparison showing a toilet in normal daylight and the same toilet illuminated by the night light in a dark environment.
Image 6.2: A close-up shot of the toilet bowl interior, showing the vibrant blue illumination provided by the LED night light.
7. Maintenance
- Cleaning: Wipe the exterior of the unit with a damp cloth. Do not use abrasive cleaners or immerse the unit in water.
- Battery Replacement: When the light dims or stops functioning, replace all three AAA batteries with new ones. Ensure proper polarity.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | 1. Insufficient darkness. 2. Dead or incorrectly installed batteries. 3. Motion sensor obstructed or faulty. | 1. Ensure the room is sufficiently dark for activation. 2. Replace batteries with new AAA batteries, checking polarity. 3. Ensure the motion sensor is clean and unobstructed. |
| Light stays on constantly or turns on randomly. | 1. Ambient light too low, causing continuous activation. 2. Motion sensor too sensitive or detecting constant movement. | 1. Ensure there is enough ambient light during the day to prevent activation. 2. Reposition the unit to avoid constant motion detection. |
| Colors do not change or are stuck on one color. | 1. Unit is in single color mode. 2. Low battery power. | 1. Press the color selection button to cycle through colors or return to automatic cycling mode. 2. Replace batteries. |
9. Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 3.78"D x 2.83"W x 1.97"H |
| Item Weight | 1.44 ounces |
| Lamp Type | Night Light |
| Shade Color | Multicolor |
| Light Source Type | LED |
| Power Source | Battery Powered (3 x AAA, not included) |
| Wattage | 5 watts |
| Control Method | Motion Sensor / Touch (for color selection) |
| Voltage | 1.5 volts |
| Additional Features | Color Changing, Motion Activated |
| UPC | 614134109982 |
| ASIN | B01ISNCU4Y |
Image 9.1: Diagram showing the key dimensions of the toilet night light unit in inches.
10. Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact the retailer from whom the product was purchased. Keep your proof of purchase for any warranty claims.