1. Introduction
The RIGID Ignite LED Diffused Flush Mount Light (Model 20631) is a compact and versatile auxiliary lighting solution. Designed for various applications including cars, trucks, motorcycles, UTVs, and marine environments, this light provides 1000 raw lumens of diffused light output. Its small footprint, approximately 1.4" x 1.4" x 2", makes it suitable for installations where space is limited. This manual provides essential information for the safe installation, operation, and maintenance of your RIGID Ignite light.
Key Features:
- Smallest forward projecting light in the RIGID product line.
- Easy installation, typically requiring a 1.75-inch hole saw.
- Wide operating voltage range: 6-28 VDC.
- Diffused beam pattern for broad, short-range illumination.
- IP68 compliant for dust and water resistance.
2. Safety Information
Please read and understand all safety instructions before installing or operating the RIGID Ignite LED Diffused Flush Mount Light. Failure to follow these instructions may result in electrical shock, fire, serious injury, or property damage.
- Always disconnect the vehicle's battery before performing any electrical work.
- Ensure all wiring connections are secure and properly insulated to prevent short circuits.
- Do not look directly into the light when it is illuminated, as it can cause temporary vision impairment.
- Mount the light securely to prevent it from becoming a projectile during vehicle operation or impact.
- Verify that the installation does not interfere with existing vehicle components or safety systems.
- Consult a professional if you are unsure about any part of the installation process.
3. Package Contents
Upon opening the package, verify that all components are present and undamaged.
- 1x RIGID Ignite LED Diffused Flush Mount Light
- Mounting Hardware (screws, nuts, washers)
- Wiring Harness (may vary by kit)
- Installation Template (may be included for drilling)
4. Product Overview
The RIGID Ignite LED Diffused Flush Mount Light is engineered for durability and performance in demanding conditions. Its compact design allows for discreet and integrated mounting.
5. Setup and Installation
Proper installation is crucial for the performance and longevity of your RIGID Ignite light. Follow these general steps for installation. Specific vehicle applications may require additional considerations.
- Choose Mounting Location: Select a flat, secure surface on your vehicle for flush mounting. Ensure there is sufficient clearance behind the mounting surface for the light housing and wiring.
- Prepare Mounting Surface: If flush mounting, use the provided template (if applicable) or measure carefully to mark the cutting area. A 1.75-inch hole saw is typically required for the main opening. Drill pilot holes for the mounting screws.
- Drill/Cut Opening: Carefully cut the marked opening and drill the mounting screw holes. Deburr any sharp edges.
- Wiring:
- Connect the positive (+) wire from the light to a fused 12V-28V power source (e.g., auxiliary switch, reverse light circuit).
- Connect the negative (-) wire from the light to a suitable ground point on the vehicle chassis.
- Ensure all connections are waterproof and protected from abrasion.
- Mount the Light: Insert the light into the prepared opening. Secure it using the provided mounting hardware (screws, nuts, washers). Do not overtighten.
- Test Functionality: Reconnect the vehicle battery. Activate the light to ensure it functions correctly. Check for proper beam pattern and illumination.
Note: For optimal performance and safety, it is recommended to use a relay and appropriate gauge wiring for your installation, especially if connecting to a high-current circuit or multiple lights.
6. Operating Instructions
The RIGID Ignite LED Diffused Flush Mount Light operates as a simple on/off auxiliary light.
- Power On: Activate the switch or circuit to which the light is connected. The light will illuminate, providing a broad, diffused beam.
- Power Off: Deactivate the switch or circuit to turn off the light.
The diffused beam pattern is designed for short-range area illumination, making it ideal for backup lights, utility lighting, or scene lighting.
7. Maintenance
The RIGID Ignite LED Diffused Flush Mount Light is designed for minimal maintenance.
- Cleaning: Periodically clean the lens with a soft cloth and mild soap and water to remove dirt, mud, or debris that may obstruct light output. Avoid abrasive cleaners or harsh chemicals.
- Inspection: Regularly inspect the mounting hardware and wiring for any signs of looseness, corrosion, or damage. Tighten any loose fasteners and repair or replace damaged wiring as needed.
- Water Resistance: While IP68 compliant, avoid directing high-pressure water sprays directly at the light for extended periods, especially at seals.
8. Troubleshooting
If your RIGID Ignite light is not functioning as expected, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power, faulty wiring, blown fuse, faulty switch. | Check power connections, ensure proper grounding, inspect fuse in the circuit, test the switch. |
| Light flickers or is dim. | Loose connection, insufficient voltage, damaged wiring. | Verify all connections are secure, check vehicle voltage, inspect wiring for damage. |
| Moisture inside the lens. | Compromised seal, improper installation. | Ensure mounting screws are tightened correctly. If moisture persists, contact customer support. |
If troubleshooting steps do not resolve the issue, contact RIGID customer support for further assistance.
9. Specifications
| Feature | Detail |
|---|---|
| Model Number | 20631 |
| Brand | RIGID |
| Light Type | LED Diffused Flush Mount |
| Raw Lumens | 1000 |
| LEDs | 1 |
| Amp Draw | 12 |
| Voltage Range | 6-28 VDC |
| Lux at 10m | 9 |
| Beam Distance | 59.9 m |
| Peak Beam Intensity | 884 cd |
| Dimensions (L x W x H) | Approximately 1.4" x 1.4" x 2" (Light) / 5 x 5 x 5 inches (Packaging) |
| Item Weight | 0.3 Pounds / 4.8 ounces |
| Water Resistance | IP68 Compliant |
| Color | Black |
| Form Factor | Pod |
| Recommended Uses | Vehicle Exterior, Vehicle Interior |
| Automotive Fit Type | Universal Fit |
| Assembly Location | Designed, engineered and assembled in USA. |
10. Warranty and Support
For information regarding the product warranty, please refer to the official RIGID Industries website or contact their customer support directly. Warranty terms and conditions may vary.
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact RIGID Industries customer support.
- Manufacturer: RIGID INDUSTIRES
- Website: www.rigidindustries.com
- Contact: Refer to the manufacturer's website for current contact information.
