1. Introduction
This user manual provides comprehensive instructions for the safe and efficient operation of the Showtec Compact Par 7 Q4 7 x 3W RGBW LED Floor PAR Spot. Please read this manual thoroughly before installation, operation, or maintenance to ensure proper use and to prevent damage to the unit or injury to personnel.
The Showtec Compact Par 7 Q4 is a compact RGBW PAR can designed for various lighting applications, offering versatile color mixing and robust performance.
2. Safety Instructions
Always observe the following safety precautions to reduce the risk of electric shock, fire, or injury:
- Ensure the power supply voltage matches the voltage specified on the unit.
- Always connect the unit to a grounded power outlet.
- Do not operate the unit if the power cord is damaged.
- Disconnect from mains power before cleaning or servicing.
- Do not expose the unit to rain or moisture.
- Maintain adequate ventilation around the unit to prevent overheating.
- Avoid direct eye exposure to the light source.
- This unit is for indoor use only.
3. Product Overview
The Showtec Compact Par 7 Q4 features seven 3W RGBW LEDs, providing a wide spectrum of colors. Its compact design makes it suitable for floor standing or truss mounting.
Figure 3.1: Front view of the Showtec Compact Par 7 Q4 with red light output, showcasing its seven powerful RGBW LEDs.
Figure 3.2: The PAR spot emitting a bright white light, demonstrating its full spectrum capabilities.
Figure 3.3: The PAR spot displaying a vibrant blue light, highlighting its color mixing versatility.
Figure 3.4: Close-up view of the LED array when the unit is off, showing the individual lenses.
Figure 3.5: Rear view of the unit, showing the power input and DMX connections (XLR 3-pin).
Figure 3.6: Angled view of the PAR spot, demonstrating the adjustable mounting bracket for floor or truss applications.
4. Setup
4.1 Unpacking
Carefully unpack the unit and check for any damage during transit. Retain the packaging material for future transport or storage.
4.2 Mounting
The Compact Par 7 Q4 can be used as a floor spot or mounted to a truss using the integrated bracket. Ensure the mounting surface or truss can support the weight of the fixture. Use appropriate clamps and safety cables when mounting overhead.
4.3 Power Connection
Connect the power cable to the unit's power input and then to a grounded electrical outlet. Verify that the local voltage matches the unit's requirements (240 Volts).
4.4 DMX Connection (Optional)
For DMX control, connect a DMX cable from your DMX controller to the DMX IN port of the fixture. If connecting multiple units, daisy-chain them by connecting the DMX OUT of the first unit to the DMX IN of the next.
5. Operating
5.1 Control Panel
The unit features a digital display and control buttons (Menu, Up, Down, Enter) on the rear for setting modes and DMX addresses.
5.2 Operating Modes
The Showtec Compact Par 7 Q4 typically offers several operating modes:
- DMX Mode: Allows control via an external DMX controller. Set the DMX address using the control panel.
- Auto Mode: Pre-programmed light shows that run automatically.
- Sound Active Mode: The light reacts to sound via a built-in microphone.
- Master/Slave Mode: Link multiple units where one acts as the master and others as slaves, synchronizing their operation.
- Static Color Mode: Select and display a single static color.
5.3 DMX Channel Chart
Refer to the specific DMX channel chart in the full product manual for detailed information on controlling each function via DMX. Common channels include Dimmer, Red, Green, Blue, White, Strobe, and Program selection.
6. Maintenance
6.1 Cleaning
Regular cleaning of the lenses and housing is recommended to maintain optimal light output and extend the unit's lifespan. Use a soft, lint-free cloth and a mild glass cleaner. Do not use abrasive materials.
6.2 Fuse Replacement
If the unit does not power on, check the fuse located near the power input. Replace it with a fuse of the same type and rating only.
6.3 Storage
When not in use, store the unit in its original packaging or a suitable flight case in a dry, dust-free environment.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not power on | No power supply; Blown fuse; Damaged power cable | Check power connection; Replace fuse; Replace cable |
| No DMX control | Incorrect DMX address; Faulty DMX cable; DMX controller issue | Verify DMX address; Check/replace DMX cable; Test controller |
| Lights flicker or behave erratically | Poor DMX signal; Overheating; Internal fault | Check DMX connections; Ensure proper ventilation; Contact support |
| Colors are incorrect | Incorrect DMX channel values; Internal calibration issue | Adjust DMX values; Perform factory reset if available; Contact support |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Showtec |
| Model | Q4 |
| Reference Number | LIG0013729-000 |
| Light Source | 7 x 3W RGBW LEDs |
| Power | 3 Watts (per LED) |
| Voltage | 240 Volts |
| Power Source | Electric Cable |
| Dimensions (L x W x H) | 31.5 x 31 x 15.5 cm |
| Weight | 2.73 Kilograms |
| ASIN | B01F04U758 |
9. Warranty and Support
Information regarding specific warranty terms and conditions for the Showtec Compact Par 7 Q4 is not available in the provided product details. Please refer to the retailer or manufacturer's official website for the most up-to-date warranty information.
For technical support, service, or spare parts inquiries, please contact your authorized Showtec dealer or the manufacturer directly. Always provide the model number (Q4) and reference number (LIG0013729-000) when seeking support.
