Technical Precision 39101600
Technical Precision Replacement Light Bulb for AGILENT/HP 39101600
Instruction Manual
1. Product Overview
This document provides instructions for the installation, operation, and maintenance of the Technical Precision Replacement Light Bulb, model 39101600. This bulb is designed as a direct replacement for AGILENT/HP equipment requiring the 39101600 light bulb.
Image 1.1: The Technical Precision Replacement Light Bulb, model 39101600. This image displays the tubular bulb with its base and attached wiring, ending in a white connector.
2. Safety Information
Read all safety instructions before installation and operation. Failure to follow these instructions may result in electric shock, fire, or other hazards.
- Always disconnect power to the equipment before attempting to install or replace the light bulb.
- Allow the old bulb to cool completely before removal to prevent burns.
- Handle the new bulb by its base or connector, avoiding direct contact with the glass to prevent contamination and potential damage.
- Ensure the replacement bulb matches the specifications of the original bulb.
- Dispose of old bulbs according to local regulations.
3. Setup and Installation
Follow these steps to safely install your new replacement light bulb:
- Power Disconnection: Locate the power source for your AGILENT/HP equipment and turn it off. Unplug the equipment from the electrical outlet to ensure no power is supplied.
- Access Bulb Compartment: Refer to your AGILENT/HP equipment's specific manual to locate and open the light bulb access compartment. This may involve removing screws or opening a latch.
- Remove Old Bulb: Carefully disconnect the wiring connector of the old bulb. Gently remove the old bulb from its socket. If the bulb is hot, wait for it to cool.
- Install New Bulb: Insert the Technical Precision 39101600 replacement bulb into the socket. Ensure it is seated firmly and correctly. Connect the wiring connector securely. Avoid forcing the bulb into place.
- Secure Compartment: Close and secure the light bulb access compartment.
- Restore Power: Plug the AGILENT/HP equipment back into the electrical outlet and turn on the power.
4. Operating Instructions
Once installed, the Technical Precision 39101600 replacement light bulb operates in conjunction with your AGILENT/HP equipment's existing controls.
- Turn on the AGILENT/HP equipment as per its operational guidelines.
- The light bulb should illuminate immediately upon activation of the relevant function within the equipment.
- If the bulb does not light, refer to the Troubleshooting section.
5. Maintenance
The Technical Precision 39101600 light bulb requires minimal maintenance. Adhere to the following guidelines to ensure optimal performance and longevity:
- Cleaning: If the bulb's glass surface becomes dusty or dirty, ensure the equipment is powered off and the bulb is cool. Gently wipe the glass with a soft, dry, lint-free cloth. Do not use abrasive cleaners or liquids.
- Inspection: Periodically inspect the bulb and its connections for any signs of wear or damage. If damage is observed, disconnect power and replace the bulb.
- Replacement: Replace the bulb when its light output diminishes significantly or if it ceases to function.
6. Troubleshooting
If the replacement light bulb does not function as expected, consider the following:
| Problem | Possible Cause | Solution |
|---|---|---|
| Bulb does not light up. | No power to equipment. | Check if the equipment is plugged in and powered on. Verify circuit breaker. |
| Bulb does not light up. | Bulb not properly seated or connected. | Disconnect power, open compartment, and re-seat the bulb and its connector. |
| Bulb does not light up. | Defective bulb. | If all other steps fail, the bulb may be defective. Contact Technical Precision support. |
| Bulb flickers or dims. | Loose connection. | Disconnect power, open compartment, and check all connections for tightness. |
| Bulb flickers or dims. | Nearing end of life. | Replace the bulb with a new one. |
7. Specifications
- Brand: Technical Precision
- Model Number: 39101600
- Compatibility: Replacement for AGILENT/HP 39101600
- Wattage: 220 Watts
- Material: Copper (base/internal components)
- Shape: Tubular
- Included Components: 1 Replacement Part (light bulb)
8. Warranty and Support
For warranty information or technical assistance, please contact Technical Precision directly. Details regarding specific warranty periods and terms are typically provided at the point of purchase or on the manufacturer's official website.
You can visit the Technical Precision Store for more information or to explore other products.