Introduction
Thank you for choosing the Child Craft Bristol Compact Crib. This manual provides essential information for the safe assembly, operation, and maintenance of your crib. Please read all instructions carefully before assembly and keep this manual for future reference.
The Child Craft Bristol Compact Crib features a low-profile design for easy infant access, a durable wood construction, and includes a 3-inch foam mattress. It is equipped with ultra-quiet casters, two of which are locking, for improved maneuverability and stability.
Important Safety Information
WARNING: Failure to follow these warnings and the assembly instructions could result in serious injury or death.
- Read all instructions before using the crib. Keep instructions for future use.
- Do not use this crib if you cannot exactly follow the accompanying instructions.
- The crib, including side rails, must be fully erected prior to use.
- Do not place the crib near a window where cords from blinds or drapes could strangle a child.
- Do not suspend strings or toys over the crib.
- Do not place the crib near heat sources, windows, or other furniture.
- Discontinue use of the crib when a child begins to climb out or reaches the height of 35 inches (89 cm).
- Check this product for damaged hardware, loose joints, missing parts, or sharp edges before and after assembly and frequently during use. Do not use the crib if any parts are missing or broken. Contact Child Craft for replacement parts and instructional literature if needed. Do not substitute parts.
- Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place extra padding under an infant.
- To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.
- Always provide the supervision necessary for the continued safety of your child.
- The mattress supplied with this crib is 3 inches thick. Ensure any replacement mattress used is at least 3 inches thick and fits snugly without gaps.
Package Contents
Before beginning assembly, ensure all parts are present. If any parts are missing or damaged, do not proceed with assembly. Contact Child Craft customer support for assistance.
- Crib Frame Components (sides, ends, mattress support)
- Hardware Pack (screws, bolts, Allen wrench)
- 4 x 3-inch Caster Wheels (2 locking, 2 non-locking)
- 1 x 3-inch Foam Mattress
- Instruction Manual
Setup and Assembly
Assembly typically requires two adults. Follow the steps below carefully. Do not overtighten fasteners.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a soft, clean surface to prevent scratching. Verify all package contents are present.
- Attach Casters: Insert the four 3-inch caster wheels into the designated holes at the bottom of each leg. Ensure the two locking casters are installed on the same side for easier access. Press firmly until they click into place.
- Assemble Crib Frame: Connect the crib ends to the side rails using the provided hardware. Ensure all connections are secure but do not fully tighten until the entire frame is assembled.
- Install Mattress Support: Position the mattress support frame within the crib. The mattress support can be adjusted to two different height positions. Choose the appropriate height based on the child's age and development. Secure the mattress support to the crib frame using the provided hardware.
- Final Tightening: Once all components are assembled, carefully tighten all screws and bolts. Do not overtighten.
- Place Mattress: Insert the 3-inch foam mattress into the crib. Ensure it fits snugly without any gaps between the mattress and the crib sides.
Image: Close-up view of a crib leg with an attached caster wheel. This illustrates how the caster wheels are installed at the base of the crib legs.
Image: Fully assembled Child Craft Bristol Compact Crib in natural wood finish, shown with the included foam mattress. This provides a complete view of the product after assembly.
Operating Instructions
Adjusting Mattress Height
The mattress support can be set to two different heights. The higher position is for infants, providing easier access for caregivers. The lower position is for older infants and toddlers who can push up on their hands and knees or stand, to prevent them from climbing out.
- Remove the mattress from the crib.
- Carefully detach the mattress support from the crib frame by unscrewing the fasteners.
- Re-attach the mattress support to the desired height position, ensuring all fasteners are securely tightened.
- Replace the mattress.
Using Caster Wheels
The crib is equipped with four 3-inch caster wheels for easy movement. Two of these casters are locking to secure the crib in place.
- To Move the Crib: Ensure both locking casters are in the unlocked position. Gently push the crib to its desired location.
- To Secure the Crib: Once the crib is in position, engage the locks on the two locking casters by pressing down on the lever. Verify the crib is stable and does not move.
Maintenance and Care
- Cleaning: Wipe the crib surfaces with a damp cloth. Avoid abrasive cleaners or strong chemicals that could damage the finish or materials.
- Hardware Check: Regularly check all screws, bolts, and fasteners to ensure they are tight and secure. Loose hardware can pose a safety hazard.
- Storage: If storing the crib, ensure it is clean and dry. Store in a climate-controlled environment to prevent warping or damage to the wood.
- Mattress Care: The foam mattress can be spot cleaned with a mild soap and water solution. Allow to air dry completely before placing back in the crib.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Crib feels wobbly or unstable. | Loose hardware. | Check and tighten all screws and bolts. Do not overtighten. |
| Casters do not roll smoothly. | Debris in wheels or casters not fully inserted. | Clean any debris from the wheels. Ensure casters are fully seated in the legs. |
| Mattress does not fit snugly. | Incorrect mattress size or improper assembly. | Ensure the correct mattress (3-inch foam mattress included) is used. Recheck crib assembly to ensure all parts are correctly aligned. |
| Crib makes squeaking noises. | Loose joints or friction between wood parts. | Tighten all hardware. Apply a small amount of paraffin wax or silicone spray to contact points if necessary. |
Specifications
- Model Number: F99040.04
- Brand: Child Craft
- Material: Wood
- Color: Natural (Beige finish)
- Assembled Dimensions (L x W x H): 39"L x 26.25"W x 38"H
- Item Weight: 52 pounds
- Maximum Weight Recommendation: 50 pounds
- Casters: 4 x 3-inch ultra-quiet casters (2 locking)
- Mattress: Includes 3-inch foam mattress
- Mattress Support: Adjustable to two positions
- Safety Certifications: Exceeds CPSC and ASTM standards, verified by Baby Safety Alliance.
Warranty Information
Child Craft products are manufactured to high-quality standards. For specific warranty details, please refer to the warranty card included with your product or contact Child Craft customer support directly. Typically, warranties cover manufacturing defects under normal use.
Customer Support
If you have any questions, require replacement parts, or need assistance with your Child Craft Bristol Compact Crib, please contact the manufacturer or your retailer.
- Manufacturer: Foundations
- Brand: Child Craft
- Refer to the product packaging or the Child Craft official website for the most current contact information.