1. Introduction
This manual provides comprehensive instructions for the safe and efficient use of the Bpt AS/200 230V Power Supply, model 61404100. Please read this manual thoroughly before installation and operation to ensure proper functionality and to prevent damage.
2. Safety Information
WARNING: Electrical shock hazard. Always disconnect power before installing or servicing this unit.
- Ensure the power supply is connected to a grounded outlet.
- Do not open the power supply casing; there are no user-serviceable parts inside.
- Keep the unit away from water, moisture, and extreme temperatures.
- Only use the power supply with compatible devices as specified.
- Installation should be performed by qualified personnel if you are unsure.
3. Package Contents
Verify that all items are present in the package:
- Bpt AS/200 230V Power Supply (Model: 61404100)
- User Manual (this document)
Figure 1: Bpt AS/200 230V Power Supply. This image shows the compact, rectangular power supply unit, typically black or grey, with various connectors visible on one side.
4. Setup and Installation
Follow these steps to properly install your Bpt AS/200 Power Supply:
- Prepare the Installation Area: Ensure the device where the power supply will be installed (e.g., computer case, audio/video equipment) is powered off and disconnected from the main power outlet.
- Mount the Power Supply: Carefully place the Bpt AS/200 into its designated slot within the compatible device. Secure it using appropriate screws (not included, typically provided with the device chassis).
- Connect Power Cables:
- Connect the 24-pin system bus connector to the motherboard or main control board of your device. Ensure it is firmly seated.
- Connect any other necessary peripheral power connectors (e.g., SATA, Molex, PCIe, if applicable to your specific setup and device) from the power supply to the respective components.
- Input Power Connection: Connect the main power cable (not included) to the power supply's input port. Ensure the power cable is rated for 230-240V AC.
- Final Check: Double-check all connections to ensure they are secure and correctly oriented.
Compatible Devices: This power supply is designed for "Altri dispositivi audio e video" (Other audio and video devices) and systems requiring an ATX type connectivity with a 24-pin bus connector.
5. Operating Instructions
Once the Bpt AS/200 Power Supply is correctly installed and all connections are secure:
- Connect to Mains Power: Plug the main power cable into a suitable 230V AC wall outlet.
- Power On Device: Turn on the main power switch of the device (e.g., computer, audio/video system) that the power supply is powering. The power supply will then provide the necessary voltage to the internal components.
- Power Off Device: To turn off, follow the standard shutdown procedure for your device, then disconnect from the mains power if the device will not be used for an extended period.
6. Maintenance
The Bpt AS/200 Power Supply is designed for reliable operation with minimal maintenance. Its cooling method is "Aria" (Air).
- Cleaning: Periodically, ensure that the ventilation openings of the power supply and the device it powers are free from dust and debris to maintain optimal airflow. Use compressed air or a soft brush for cleaning.
- Environment: Operate the power supply in a well-ventilated area, free from excessive dust, humidity, and direct sunlight.
- Inspection: Occasionally inspect power cables for any signs of damage or wear. Replace damaged cables immediately.
7. Troubleshooting
If you encounter issues with your Bpt AS/200 Power Supply, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | No power from wall outlet, loose power cable, faulty power supply. | Check wall outlet with another device. Ensure all power cables are securely connected. If problem persists, the power supply may be faulty and require replacement. |
| Intermittent power. | Loose internal connections, overheating. | Verify all internal power connectors are firmly seated. Ensure adequate ventilation to prevent overheating. |
| Unusual noises from the power supply. | Fan obstruction or failure. | Disconnect power and inspect for any obstructions in the fan area. If the noise persists or is accompanied by overheating, discontinue use and seek professional assistance. |
If troubleshooting steps do not resolve the issue, contact customer support or a qualified technician.
8. Specifications
| Brand | Bpt |
| Model Name / Number | AS/200 (61404100) |
| Input Voltage (Minimum) | 230 Volt (AC) |
| Input Voltage (Maximum) | 240 Volt (AC) |
| Cooling Method | Air |
| Item Dimensions (LxWxH) | 10 x 5 x 10 cm |
| Device Connectivity Type | ATX |
| System Bus Connector Type | 24 pin |
| Compatible Devices | Other audio and video devices |
| GTIN | 08004487064816 |
| Country of Origin | Italy |
9. Warranty Information
According to product specifications, a product warranty is "Non applicabile" (Not applicable). Please refer to your point of purchase for any return or exchange policies.
10. Support
For technical assistance or further inquiries regarding the Bpt AS/200 230V Power Supply, please contact your retailer or the manufacturer, Bpt S.P.A., directly. Ensure you have your product model number (61404100) available when seeking support.