Q-BAIHE Laser Module Housing 33x33x50mm User Manual

Introduction

This manual provides comprehensive instructions for the Q-BAIHE Laser Module Housing, designed for 9.0mm TO-5 laser diodes. This housing features integrated cooling fans and is compatible with 405nm-480nm violet/blue laser diodes, utilizing a coated glass lens for optimal performance. Please read this manual thoroughly before installation and operation to ensure proper use and safety.

Safety Information

Always wear appropriate laser safety glasses when working with laser diodes.
Ensure the laser diode is correctly installed and secured within the housing.
Do not look directly into the laser beam or allow it to strike reflective surfaces.
Disconnect power before performing any maintenance or adjustments.
Keep the device away from children and unauthorized personnel.

Package Contents

Verify that all items listed below are present in your package:

1x Laser Module Housing (33x33x50mm)
1x Cooling Fan (pre-attached or separate)
1x Coated Glass Lens (suitable for 405nm-480nm violet/blue laser)
Mounting Screws and accessories (e.g., spring, plastic spacers)

Disassembled Q-BAIHE Laser Module Housing components

Figure 1: Components included with the Q-BAIHE Laser Module Housing. This image shows the main housing, a separate cooling fan, a set of screws, a spring, and plastic spacers.

Setup and Assembly

Prepare the Laser Diode: Ensure your 9.0mm TO-5 laser diode is clean and free of dust.
Insert Laser Diode: Carefully insert the 9.0mm TO-5 laser diode into the designated slot within the housing. Ensure proper orientation.
Install Lens: Screw the coated glass lens into the front of the housing. Be gentle to avoid cross-threading. The lens is designed for 405nm-480nm violet/blue lasers. (Note: Lens type, full-thread or half-thread, may vary and will be sent randomly.)
Mount Cooling Fan: If the fan is not pre-attached, secure it to the housing using the provided screws and spacers. Ensure the fan's airflow is directed to optimize cooling for the laser diode.
Connect Power: Connect the fan's power wires to an appropriate power source. Observe correct polarity (typically red for positive, black for negative).

Assembled Q-BAIHE Laser Module Housing with fan

Figure 2: Fully assembled Q-BAIHE Laser Module Housing, showing the heatsink fins and the attached cooling fan.

Operating Instructions

Once assembled, the laser module housing is ready for integration into your laser system. Ensure the laser diode itself is properly powered and controlled according to its specifications.

Power On: Apply power to the cooling fan. The fan should begin to rotate, providing active cooling to the laser diode.
Laser Diode Operation: Operate your 9.0mm TO-5 laser diode according to its manufacturer's guidelines. The housing's heatsink and fan are designed to dissipate heat generated during operation.
Monitoring: Periodically monitor the temperature of the housing during extended operation to ensure adequate cooling.

Maintenance

Cleaning: Keep the heatsink fins and fan blades free of dust and debris to ensure efficient cooling. Use a soft brush or compressed air for cleaning.
Lens Care: If necessary, gently clean the glass lens with a lens cleaning solution and a microfiber cloth. Avoid scratching the coated surface.
Fan Inspection: Periodically check the cooling fan for proper operation. Replace if it becomes noisy or stops rotating.

Troubleshooting

Problem	Possible Cause	Solution
Fan not spinning	No power, incorrect polarity, faulty fan.	Check power connection and polarity. Test fan with a known good power source. Replace fan if faulty.
Overheating of laser diode	Insufficient airflow, clogged heatsink, fan malfunction.	Clean heatsink fins and fan. Ensure fan is operating correctly. Verify laser diode is not exceeding its power limits.
Poor laser beam quality	Dirty or misaligned lens.	Clean the lens. Re-check lens installation and alignment.

Specifications

Model Number	Case-333350-TO5+Collim-405-G
Dimensions	33mm x 33mm x 50mm (Length x Width x Height)
Compatible Laser Diode	9.0mm TO-5 package
Compatible Laser Wavelengths	405nm - 480nm (Violet/Blue Laser)
Lens Type	Coated Glass Lens
Cooling	Integrated Fan and Heatsink
Material	Metal (Housing), Glass (Lens)

Support

For technical assistance or further inquiries, please contact Q-BAIHE customer support. Assembly diagrams may be provided upon request.

	Laserland Fat Beam Laser Module Product Specification Detailed product specification for the Laserland Fat Beam Laser Module, covering its appearance, main technical parameters, and critical safety precautions for operation and handling.
	Hydrawav3: Advanced Recovery and Wellness Device - Technical Overview Explore the Hydrawav3 device, a multifaceted tool for non-invasive recovery. Learn about its advanced therapeutic modalities, protocols, contraindications, and technical specifications for pain management, enhanced range of motion, and wellness.
	Chroma Radiance User Guide: Advanced Skin Health and Vitality Explore the Chroma Radiance user guide for detailed information on its features, technical specifications, usage instructions, and safety guidelines for advanced skin health and vitality.
	Laser Tree LT-405-3W-FC 405nm 3W Fiber Coupled UV Diode Laser Datasheet Technical datasheet for the Laser Tree LT-405-3W-FC, a 405nm, 3W UV diode laser module featuring selectable fiber core diameters (100um, 200um, 400um, 800um). Applications include medical treatment, industrial marking, and special light sources. This document details absolute maximum ratings, optical and electrical characteristics, outline dimensions for models 4LD-A1 and 4LD-B, and essential safety cautions for handling and operation.
	MelodySusie Nail Lamp User Manual User manual for the MelodySusie Nail Lamp, detailing item inclusion, parts, specifications, and operating instructions. Includes contact information and representative details.

Q-BAIHE Case-333350-TO5+Collim-405-G