Introduction
This manual provides detailed instructions for the installation, maintenance, and general information regarding the Bissell PowerForce Bagless Upright Vacuum Foam and HEPA Filter Assembly. Proper maintenance of your vacuum's filters ensures optimal performance and extends the life of your appliance.
Compatible Models
This filter assembly is compatible with various Bissell PowerForce and Helix series upright vacuum cleaners, including but not limited to:
- CleanView Helix Plus Vacuum: 22C1, 22C12, 32Y7
- PowerForce Bagless: 6594, 6594F, 6594G, 6594J, 6594R, 6594W, 6596R
- PowerForce Bagless Vacuum: 6582, 6579, 65793, 65823, 6582R
- PowerForce Helix Bagless: 12B1, 1240, 1240U, 1240V, 1240W, 12B1C, 12B1D, 12B1E, 12B1R, 12B1U, 12B1V, 12B1W
- PowerForce Helix Turbo Bagless Vacuum: 68C71, 2140, 68C7, 68C7C, 68C7R, 68C7U, 68C7V, 68C7W
- PowerGroom Helix Rewind Vacuum: 98N4, 948N41, 98N41, 98N4W
- Rewind CleanView Pet Vacuum: 18M9W, 18M9X
This filter replaces legacy part number 203-2587.
Setup and Installation
The filter assembly consists of an outer foam filter and an inner pleated filter. These are designed to work together to capture dust and allergens.
Figure 1: The complete filter assembly, consisting of an outer foam filter and an inner pleated HEPA filter, designed for Bissell PowerForce Bagless Upright Vacuums.
- Remove the Dirt Bin: Unplug your vacuum cleaner. Locate and remove the dirt bin from your vacuum.
- Access the Filter: The filter assembly is typically located in the lower part of the dirt bin. Twist the filter counter-clockwise to unlock and lift it out.
- Separate Filters: Gently separate the outer foam filter from the inner pleated filter.
- Install New Filters: Place the new pleated filter into the filter housing, then fit the foam filter over it. Ensure both are seated correctly.
- Reassemble: Insert the assembled filter back into the dirt bin, twisting clockwise to secure it. Reattach the dirt bin to the vacuum cleaner.
Video Guide: Filter Installation
Video 1: This video demonstrates the process of separating the outer foam filter from the inner pleated filter, and then reassembling them. It also shows the filters being removed from their packaging.
Video 2: This video illustrates the separation and reassembly of the foam and pleated filters, providing a visual guide for proper installation.
Video 3: This video demonstrates how to remove and replace the pre-motor filter from a Bissell PowerForce vacuum, including the foam and pleated components.
Maintenance
Regular cleaning and replacement of your vacuum filters are crucial for maintaining suction power and air quality.
Cleaning the Filters
- Separate Filters: Remove the filter assembly from the vacuum and separate the outer foam filter from the inner pleated filter.
- Wash: Both filters are washable. Hand wash them in warm water. A mild detergent may be used if desired.
- Rinse: Rinse thoroughly until the water runs clear.
- Dry: Allow both filters to air dry completely before reassembling and replacing them in the vacuum. Ensure they are completely dry to prevent mold or mildew growth.
Video Guide: Filter Cleaning
Video 4: This video demonstrates how to wash the foam and pleated filters under running water, emphasizing the importance of complete drying before reuse.
Video 5: A visual guide on cleaning the foam and pleated filters, showing the rinsing process to remove accumulated debris.
Video 6: This video illustrates the proper method for washing both the foam and pleated components of the vacuum filter.
Replacement Frequency: Filters should be checked monthly and washed or replaced every 3 to 6 months, depending on usage frequency and the level of dirt accumulation.
Troubleshooting
If your vacuum experiences reduced suction, the primary cause is often a dirty or clogged filter. Follow the maintenance steps above to clean or replace the filter assembly. Ensure all filter components are completely dry before reinstallation.
If reduced suction persists after cleaning or replacing the filter, check for blockages in the hose, brush roll, or dirt bin pathways.
Specifications
| Brand | Bissell |
| Material | Foam |
| Number of Pieces | 2 (Outer Foam Filter, Inner Pleated Filter) |
| Reusability | Washable (Foam and Pleated filters) |
| Item Weight | 3.73 ounces |
| Package Dimensions | 6.34 x 5.71 x 3.39 inches |
| Compatible Devices | Bissell Upright Vacuum Cleaners (various PowerForce and Helix models) |
Warranty and Support
For specific warranty information or further technical support, please refer to your original Bissell vacuum cleaner manual or visit the official Bissell website. You can also contact Bissell customer service directly for assistance with replacement parts or product inquiries.
