Sunbeam Electric Overblanket Instruction Manual

Introduction and Important Safeguards

Thank you for choosing the Sunbeam Electric Overblanket. This manual provides essential information for the safe and efficient use of your new heated blanket. Please read all instructions carefully before use and retain for future reference.

General Safety Warnings

• Do not use with an infant, child, incapacitated person, or anyone insensitive to heat.
• Do not use with pets.
• Never use the blanket if it is wet.
• Do not dry clean this product. Dry cleaning solvents may damage the insulation of the heating element.
• Regularly inspect the blanket and power cord for any signs of wear or damage. If damaged, discontinue use immediately and contact customer support.
• Ensure the controller is not covered or placed under the blanket during operation to prevent overheating.

Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Image: Sunbeam Electric Overblanket, Queen size, Walnut color. This image displays the overall appearance of the blanket.

Setup Instructions

1. Unpack the Blanket: Carefully remove the electric overblanket from its packaging. Retain all packaging materials for storage or in case of return.
2. Position on Bed: Place the electric overblanket directly on top of your mattress, ensuring it is spread evenly. The blanket should be positioned so that the connector for the control is at the foot of the bed.
3. Connect Controller: Firmly plug the controller cord into the blanket connector located at the foot of the blanket. Ensure a secure connection.
4. Plug into Power Outlet: Plug the power cord from the controller into a standard 120V AC electrical outlet. Do not use with extension cords or power strips.
5. Controller Placement: Place the controller in an easily accessible location, such as a nightstand, ensuring it will not be covered by other bedding or fall onto the floor.

Operating Instructions

Using the Controller

Image: The Sunbeam electric blanket controller, showing the On/Off button, a dial for heat settings (1-10), and an indicator for the 10-hour auto-off function.

• Power On/Off: Press the 'On/Off' button to turn the blanket on or off.
• Adjust Heat Settings: Use the dial on the controller to select one of the 10 available heat settings. Start with a lower setting and adjust as needed for your comfort.
• Preheat Function: For optimal warmth, turn the blanket on to a higher setting approximately 15-30 minutes before use to preheat your bed.
• 10-Hour Auto-Off: The blanket is equipped with a safety feature that automatically turns off the heat after 10 hours of continuous operation. This helps conserve energy and provides peace of mind.

ThermoFine Technology

Image: A graphic representing ThermoFine technology, indicating its ability to auto-adjust for consistent heat distribution across the blanket.

The Sunbeam Electric Overblanket features exclusive ThermoFine technology. This advanced wiring system senses and automatically adjusts the heat throughout the blanket to maintain a consistent and comfortable temperature, ensuring even warmth.

Note: The appearance of the controller may vary slightly from the image shown.

Maintenance and Care

Proper care will extend the life of your electric overblanket. This blanket is machine washable and dryer safe.

Washing Instructions

Image: A person loading a blanket into a washing machine, illustrating the machine washable feature.

1. Disconnect Power: Always unplug the power cord from the wall outlet and disconnect the controller(s) from the blanket before washing.
2. Pre-soak (Optional): For best results, pre-soak the blanket for 15 minutes in cold water with a small amount of mild detergent.
3. Machine Wash: Wash on the 'delicate' or 'gentle' cycle in a commercial washing machine (top-loading or front-loading without a center agitator) using cold water and a small amount of mild, non-bleach detergent. Do not use bleach.
4. Rinse: Rinse on the 'normal' cycle.

Drying Instructions

1. Tumble Dry: Tumble dry on a low heat setting in a commercial dryer until damp. Do not use high heat.
2. Air Dry: Remove the blanket from the dryer while still damp and drape it over a clothesline or shower rod to air dry completely. Ensure the blanket is fully dry before reconnecting the controller and using.
3. Do Not Iron: Do not iron the electric blanket.

Troubleshooting

If your Sunbeam Electric Overblanket is not functioning as expected, please refer to the following common issues and solutions:

If you experience any issues not listed here, or if the problem persists after attempting the suggested solutions, please contact Sunbeam customer support.

Specifications

• Model Number: BSV9GQS-R470-12A44
• Brand: Sunbeam
• Material: Velvet Plush
• Color: Walnut
• Size: Queen (approximately 84"L x 90"W)
• Heat Settings: 10
• Auto-Off Feature: 10-Hour
• Special Features: ThermoFine Technology, Preheat Function, Adjustable Heat Settings
• Item Weight: 5.9 Pounds
• UPC: 027045784689, 027045785822

Image: Bedding Size Guide. This chart provides standard dimensions for various blanket sizes, including Queen (84" x 90").

Warranty and Support

Limited Warranty

This Sunbeam Electric Overblanket is covered by a 5-Year Limited Manufacturer's Warranty. This warranty covers defects in materials and workmanship under normal use. Please refer to the warranty documentation included with your product for full terms and conditions, including how to make a claim.

Customer Support

For technical assistance, troubleshooting, or warranty inquiries, please visit the official Sunbeam website or refer to the contact information provided in your product packaging. Have your model number (BSV9GQS-R470-12A44) ready when contacting support.

You can also visit the Sunbeam Store on Amazon for additional product information and resources.