Orion Motor Tech 8x6.5 Wheel Spacers Instruction Manual

Introduction

This manual provides detailed instructions for the safe and proper installation and maintenance of your Orion Motor Tech 8x6.5 Wheel Spacers. These 2-inch wheel adapters are designed to improve vehicle stability and handling by widening the axle track. Please read all instructions carefully before beginning installation.

Image: A set of four Orion Motor Tech 8x6.5 wheel spacers, showcasing their design and components.

Product Features

• Safe and Secure: Improves cornering, stability, handling, and control by adding 4 inches to the axle track.
• Premium Material: Made from solid blocks of T6 aircraft-grade aluminum for lightweight durability and strength.
• Dacromet-Coated Bolts: Features 32 zinc-coated 9/16"-18 bolts that are heat-treated for superior strength and resistance to wear and tear.
• Unique Slotting: Custom slots on the rear face allow for easier removal and reduce potential damage during use.
• Precision Machined: Spacers are precision machined with a 60-degree taper for exceptional safety and stability.

Image: Detailed view of the wheel spacer's construction, emphasizing the anodic-oxide coating, dacromet-coated bolts, and 6061-T6 aluminum.

Image: Illustration of the unique slotting feature on the wheel spacer, designed for easy removal.

Compatibility

This wheel adapter set is compatible with various 1988 to 2011 Ram and Ford vehicles. Please verify your vehicle's specifications against the following requirements:

• Compatible Models: 1994-2011 Dodge Ram 2500, 1994-2011 Dodge Ram 3500, 1988-1998 Ford F-250, 1988-1998 Ford F-350.
• Bolt Pattern: 8x6.5" (8x165.1mm)
• Hub Bore: 130 mm
• Thread Size: 9/16"-18
• Thickness: 2 inches

Important Compatibility Checks:

1. Your vehicle's central bore must be the same as (or smaller than) the spacer's bore.
2. The bolt pattern of the spacers must match those on your vehicle & tires.
3. Your vehicle's studs must be shorter than the spacer's thickness.
4. Your existing fender clearance must be greater than the spacer's thickness.

Image: Visual guide illustrating critical compatibility checks for proper wheel spacer fitment.

Setup and Installation

Proper installation is crucial for safety and performance. If you are unsure about any step, please consult a qualified mechanic.

Required Tools (Not Included):

• Torque Wrench
• Lug Wrench or Socket Set
• Jack and Jack Stands
• Wheel Chocks
• Wire Brush or Abrasive Pad (for cleaning hub surface)
• Threadlocker (medium strength, e.g., Loctite 242)

Installation Steps:

1. Prepare Vehicle: Park the vehicle on a flat, level surface. Engage the parking brake and place wheel chocks on the wheels that will remain on the ground. Loosen the lug nuts on the wheel(s) you intend to work on.
2. Lift Vehicle: Safely lift the vehicle using a jack and secure it with jack stands. Remove the lug nuts and the wheel.
3. Clean Hub Surface: Thoroughly clean the vehicle's hub mounting surface using a wire brush or abrasive pad. Remove any rust, dirt, or debris to ensure a flat mating surface for the spacer.
4. Install Spacer: Place the wheel spacer onto the vehicle's hub. Ensure it sits flush against the hub. Apply a small amount of medium-strength threadlocker to the vehicle's existing wheel studs.
5. Secure Spacer: Install the provided spacer lug nuts onto the vehicle's studs, securing the spacer to the hub. Tighten these lug nuts in a star pattern to the manufacturer's specified torque (typically 90-100 ft-lbs for 9/16"-18 studs, but always refer to your vehicle's manual for exact specifications).
6. Mount Wheel: Place your wheel onto the newly installed wheel spacer's studs. Install your original lug nuts onto the spacer's studs.
7. Torque Wheel: Tighten your original lug nuts in a star pattern to your vehicle's manufacturer's specified torque.
8. Lower Vehicle: Carefully lower the vehicle and remove the jack stands and wheel chocks.
9. Repeat: Repeat the process for all remaining wheels.

Image: Exploded view diagram showing the components and their assembly order during wheel spacer installation.

Image: Visual comparison demonstrating the effect of installed wheel spacers on a vehicle's stance.

Installation Video:

Video: An official installation guide for Orion Motor Tech Wheel Spacers, demonstrating the steps for proper and safe mounting.

Operating and Maintenance

After installation, it is important to perform regular checks to ensure the continued safety and performance of your wheel spacers.

Post-Installation Checks:

• After the first 50-100 miles of driving, re-torque all lug nuts (both spacer-to-hub and wheel-to-spacer) to the specified values.
• Periodically check lug nut torque at regular service intervals (e.g., every oil change or tire rotation).
• Listen for any unusual noises or vibrations, which could indicate loose components.

General Maintenance:

• Keep the wheel spacers clean and free from excessive dirt or corrosive materials.
• Inspect the spacers for any signs of damage, cracks, or corrosion during tire rotations or other vehicle maintenance.
• Ensure proper tire pressure is maintained as per your vehicle's recommendations.

Troubleshooting

Specifications

Warranty and Support

For information regarding product warranty or technical support, please refer to the official Orion Motor Tech website or contact their customer service directly. Specific warranty details are not provided in this manual.