1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Warming Systems 90 Sqft 120V Electric Tile Radiant Floor Heating Mat and UDG4-4999 Touch Screen Programmable Thermostat. The electric radiant floor heat system is designed to provide luxurious warmth, making floors comfortably warm. Heat rises from the system, warming objects in the room for enhanced comfort.
Figure 1: Complete Warming Systems 90 Sqft Electric Tile Radiant Floor Heating Mat Kit.
Video 1: An overview of Warming Systems Electric Floor Heat, demonstrating its benefits and general installation concepts.
2. Important Safety Information
WARNING:
- Do not install the heating mat if the wire is damaged. This could cause an electrical hazard.
- Always use the GFCI protected thermostat to prevent electrical shock.
3. Setup and Installation
The Warming Systems Electric Radiant Floor Heating Mat is designed for straightforward installation. It includes a 90 square foot mat (20" wide x 54' long, consisting of two mats that connect at the thermostat), a UDG4-4999 Touch Screen GFCI Protected Digital Programmable Thermostat with a floor sensor, and an Installation Warning Monitor (which alarms if the wire is damaged during installation).
Figure 2: Detailed view of the kit components, including the heating mat, thermostat, sensor, and monitor.
3.1 Mat Placement
The mat is designed to be flipped and turned to fit various room shapes. It features double-sided tape on both sides for secure adhesion to any sub-floor, ensuring it lays flat during installation. The mat is 1/8” thick, UL Listed for USA and Canada, and safe for wet areas.
Figure 3: Double-sided tape on the heating mat for easy installation.
Figure 4: Heating mat properly laid out on a sub-floor.
3.2 Sizing and Layout Guidelines
When planning your installation, ensure proper clearances and avoid cutting the red heating wire. The white fiberglass mesh can be cut to facilitate turning and shaping the mat.
- Maintain at least 2" from walls and fixtures.
- Maintain at least 6" to the center of a toilet wax ring.
- Maintain at least 3" from HVAC vents or other heating appliances.
- Heating systems must be fully covered with mortar or self-leveling compound.
- The wire can be removed from the mesh and laid loose on the floor using hot glue for specific areas, such as around a toilet.
Figure 5: Layout diagram for selecting the correct mat size and ensuring proper clearances.
Video 2: A short demonstration of electric floor heat mat installation, showing how the mat can be manipulated to fit a room.
4. Operating the Thermostat
The UDG4-4999 Touch Screen GFCI Protected Digital Programmable Thermostat allows for easy and accurate control of the floor temperature, maximizing comfort and energy savings. The thermostat is 120 Volts and rated for 16 Amps.
Figure 6: UDG4-4999 Thermostat controls and indicators.
4.1 Thermostat Features
- GFCI Test Button: Used to test the Ground Fault Circuit Interrupter.
- Day and Time: Displays current day and time.
- Current Temperature: Shows the current floor temperature.
- Heating Indicator: Indicates when the system is actively heating.
- Target Temperature: The desired floor temperature setting.
- Menu: Accesses thermostat settings and programming options.
- Touch Screen: For interactive control.
- Adjust Temperature: Buttons to increase or decrease the target temperature.
- Adjust Schedule: Allows programming of heating schedules.
- On/Off/GFCI Reset Button (Side): Power control and GFCI reset.
Refer to the detailed thermostat manual for advanced programming and troubleshooting specific to the UDG4-4999 model.
5. Maintenance
The Warming Systems Electric Tile Radiant Floor Heating Mat system is designed for minimal maintenance once properly installed. Regular cleaning of the thermostat screen with a soft, dry cloth is recommended. No other routine maintenance is typically required for the heating mat itself.
6. Troubleshooting
For issues related to the heating system, first check the GFCI on the thermostat. If the GFCI trips, press the reset button. If the problem persists or if the mat is not heating as expected, consult the detailed thermostat manual for specific troubleshooting steps or contact Warming Systems Engineering Support.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | 90mat120-20-OJ |
| Mat Size | 90 Sq Ft (20" Wide x 54' Long) |
| Voltage | 120 Volts (AC) |
| Amperage Capacity | 9 Amps |
| Wattage | 1080 Watts |
| Watts/Sqft | 12 Watts/Sqft |
| Mat Thickness | 1/8" |
| Thermostat Model | UDG4-4999 (Touch Screen, GFCI Protected, Programmable) |
| Thermostat Amperage | 16 Amps |
| Certifications | UL Listed for USA and Canada |
| Material | Mesh mat and electrical wire |
| Item Weight | 8.98 pounds |
| Product Dimensions | 648 x 20 x 0.13 inches |
8. Warranty Information
Warming Systems stands behind its product with a 25-year warranty. Please retain your proof of purchase for warranty claims.
9. Customer Support
Warming Systems is a full-support manufacturer. For any questions regarding design, layout, installation, or technical assistance, our engineering support team is available to help. Contact information can typically be found on the product packaging or the official Warming Systems website.
Frequently Asked Questions (FAQs)
- Why purchase from Warming Systems? We manufacture a high-quality product, offer design and layout assistance, can answer all installation questions, and have engineers ready to answer your calls.
- About Warming Systems: We are a family-run business passionate about the comfort of warm floors, leading in Electric Floor Heat for over 20 years with tens of thousands of satisfied customers. Our manufacturing facility is located in Spring Grove, Illinois, USA.