1. Introduction
1.1 Product Overview
This manual provides instructions for the safe and effective use of the Westinghouse 0497200 200W T3 Halogen Double-Ended Clear Light Bulb with RSC Base. This bulb is designed to provide bright white light for various indoor applications.
1.2 Key Features
- Clear finish, halogen light source.
- RSC base type for double-ended fixtures.
- 200 watts power consumption, 120 volt operation.
- Average rated life of 2,000 hours.
- Light appearance: 2900 Kelvin (Bright White).
- Brightness: 3200 Lumens.
Figure 1: Westinghouse 200W T3 Halogen Double-Ended Clear Light Bulb. This image displays the clear glass bulb with its internal filament and the white ceramic RSC base at both ends.
2. Safety Information
Please read and understand all safety instructions before installing or operating this light bulb. Failure to follow these instructions may result in electric shock, fire, or personal injury.
- Risk of Electric Shock: Always disconnect power to the fixture before installing, removing, or servicing the bulb.
- Risk of Burns: Halogen bulbs operate at high temperatures. Do not touch the bulb with bare hands during operation or immediately after turning off. Allow the bulb to cool completely before handling.
- Do Not Touch Glass: Oils from skin can create hot spots on the bulb's surface, leading to premature failure or shattering. Handle the bulb by its ceramic ends or use a clean cloth or gloves.
- Proper Fixture: Use only in fixtures rated for 200 watts or higher and designed for T3 double-ended RSC base halogen bulbs.
- Indoor Use Only: This bulb is intended for indoor applications only. Do not expose to water or moisture.
- Ventilation: Ensure adequate ventilation around the bulb to prevent overheating.
- Disposal: Dispose of used bulbs according to local regulations.
3. Installation
3.1 Before Installation
- Ensure the power to the light fixture is turned OFF at the circuit breaker or fuse box.
- Allow the old bulb (if any) to cool completely before removal.
- Verify that the new Westinghouse 0497200 bulb matches the wattage, voltage, and base type (RSC) required by your fixture.
3.2 Installation Steps
- Carefully remove the new bulb from its packaging. Handle the bulb by its ceramic ends, avoiding contact with the glass envelope.
- If replacing an old bulb, gently pull it straight out from the spring-loaded sockets.
- Align the ceramic ends of the new bulb with the sockets in the fixture.
- Gently push one end of the bulb into its socket, compressing the spring. Then, insert the other end into its socket. Ensure both ends are securely seated.
- Do not force the bulb into the sockets. If it does not fit, recheck the base type and bulb length.
- Once the bulb is securely in place, restore power to the fixture.
Figure 2: Westinghouse 200W T3 Halogen Light Bulb Packaging. The packaging illustrates the bulb's T3 shape, 200W power, 120V voltage, 2,000 hours life, and RSC base type, along with a 'do not touch' symbol.
4. Operation
4.1 Turning On/Off
Once installed, the Westinghouse 0497200 bulb operates like any standard light bulb. Use the fixture's switch to turn the light on or off. This bulb is designed for instant full brightness.
4.2 Light Characteristics
- Light Color: The bulb produces a bright white light with a color temperature of 2900 Kelvin.
- Brightness: It provides 3200 lumens of illumination.
- Warm-up Time: Halogen bulbs provide full brightness immediately upon switching on.
5. Maintenance
5.1 Cleaning
To maintain optimal performance and bulb life, keep the bulb's glass surface clean. If cleaning is necessary, ensure the power is off and the bulb is cool. Use a clean, dry, lint-free cloth to gently wipe the glass. Avoid using liquid cleaners, which can leave residues that may damage the bulb or cause hot spots.
5.2 Replacement
The average rated life of this bulb is 2,000 hours. When the bulb reaches the end of its life or fails, follow the safety precautions in Section 2 and the installation steps in Section 3 to replace it with a new Westinghouse 0497200 or equivalent bulb.
6. Troubleshooting
If the bulb does not light up after installation, consider the following:
| Problem | Possible Cause | Solution |
|---|---|---|
| Bulb does not light up. | No power to the fixture. | Check circuit breaker or wall switch. Ensure power is restored. |
| Bulb not properly seated. | Turn off power, allow bulb to cool, then re-seat the bulb firmly in the sockets. | |
| Bulb is faulty or has reached end of life. | Replace with a new bulb. | |
| Fixture is faulty. | Test with a known working bulb or consult a qualified electrician. | |
| Bulb flickers. | Loose connection. | Turn off power, allow bulb to cool, then re-seat the bulb firmly. |
| Incompatible dimmer switch. | Ensure the dimmer switch is compatible with halogen bulbs and rated for the bulb's wattage. |
7. Specifications
| Specification | Detail |
|---|---|
| Brand | Westinghouse |
| Model Number | 0497200 |
| Light Type | Halogen |
| Wattage | 200 Watts |
| Voltage | 120 Volts |
| Bulb Shape Size | T3 |
| Base Type | RSC (Double-Ended) |
| Light Color | Bright White |
| Color Temperature | 2900 Kelvin |
| Brightness | 3200 Lumens |
| Average Life | 2,000 Hours |
| Finish | Clear |
| Product Dimensions | 3.07 x 0.38 x 6.49 inches |
| Item Weight | 0.32 ounces (9.07 g) |
| Material | Copper (filament/internal components) |
| Indoor/Outdoor Usage | Indoor Use Only |
8. Warranty and Support
8.1 Warranty Information
Specific warranty details for the Westinghouse 0497200 200W T3 Halogen Light Bulb are typically provided with the product packaging or can be found on the official Westinghouse website. Please retain your proof of purchase for warranty claims.
8.2 Customer Support
For further assistance, technical support, or inquiries regarding this product, please contact Westinghouse customer service through their official website or the contact information provided on the product packaging.