1. Introduction
The Mr Beams MBN350 Networked LED Wireless Motion Sensing Spotlight System utilizes NetBright technology to provide synchronized, motion-activated lighting. This system allows multiple spotlights to communicate wirelessly, ensuring that when one unit detects motion, all connected units activate simultaneously. This creates an expansive and effective lighting perimeter for enhanced visibility and security around your home or property.
This manual provides detailed instructions for the setup, operation, and maintenance of your Mr Beams MBN350 spotlight system.
Video 1.1: Official overview of the Mr. Beams NetBright Wireless Motion-Sensor Spotlight system. This video demonstrates the synchronized lighting capabilities and ease of installation.
2. Safety Information
Please read all safety instructions before installing or operating your Mr Beams MBN350 spotlight. Failure to follow these instructions may result in injury or product damage.
- Battery Safety: Use only the specified battery type (3 D-Cell batteries, not included). Do not mix old and new batteries, or different types of batteries. Ensure correct polarity when inserting batteries. Remove batteries if the unit will not be used for an extended period.
- Outdoor Use: This product is designed for outdoor use. However, it is NOT Water Resistant. Mount the spotlight in a location protected from direct heavy rain or prolonged exposure to moisture to prevent damage.
- Mounting: Ensure the mounting surface is stable and can support the weight of the spotlight. Do not mount near flammable materials or in areas with excessive heat.
- Light Source: The LED light source is non-replaceable. Do not attempt to disassemble the light fixture.
3. Package Contents
Verify that all components are present in your package:
- Mr Beams MBN350 Networked LED Wireless Motion Sensing Spotlight
- Installation and Setup Instructions
Note: 3 D-Cell batteries are required for operation and are not included.
4. Setup
Follow these steps to set up your Mr Beams MBN350 spotlight:
4.1. Battery Installation
- Twist the back cover of the spotlight counter-clockwise to open the battery compartment.
- Insert 3 new D-Cell batteries, ensuring correct polarity (+/-).
- Replace the back cover and twist clockwise to secure it.
4.2. Mounting the Spotlight
The spotlight can be mounted on various surfaces using the included hardware. Choose a location that provides the desired coverage and is protected from direct heavy rain.
Figure 4.1: Installing the Mr Beams MBN350 spotlight. The spotlight attaches to a mounting base, which is then secured to a surface.
- Select a suitable mounting location. The spotlight is designed for wall mount or similar flush mount installations.
- Secure the mounting base to the desired surface using appropriate screws.
- Attach the spotlight fixture to the mounting base and adjust the angle as needed.
4.3. Networking Multiple Spotlights (NetBright Technology)
The NetBright system allows multiple spotlights to communicate. Up to 50 NetBright spotlights can be connected per network, with an effective connectivity range of up to 150 feet between units. Non-NetBright Mr. Beams spotlights cannot be connected to this network.
To create different lighting zones, you can set up multiple networks. Refer to the specific instructions included with your product for setting network channels, if applicable.
5. Operating Instructions
The Mr Beams MBN350 spotlight is designed for automatic, motion-activated operation.
5.1. Motion Activation
The integrated motion sensor detects movement from 15 to 30 feet away. When motion is detected, the spotlight will activate.
5.2. Light Sensor
The spotlight includes a light sensor that ensures it only activates in low-light conditions or at night. It will not turn on during daylight hours, conserving battery life.
5.3. Synchronized Lighting
Thanks to NetBright technology, when one spotlight in your network senses motion, all other spotlights on the same network will instantly activate. This provides comprehensive illumination across your desired area.
Figure 5.1: Multiple spotlights providing synchronized illumination in a backyard setting.
Figure 5.2: Synchronized spotlights illuminating a path, demonstrating extended coverage.
6. Maintenance
6.1. Battery Replacement
When the light output diminishes or the spotlight stops activating, it is time to replace the batteries. Follow the battery installation steps in Section 4.1.
6.2. Cleaning
Wipe the spotlight's exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the motion sensor and light sensor lenses are clean and free of obstructions for optimal performance.
6.3. Water Protection
As the unit is not water resistant, regularly inspect the mounting location and the unit itself for any signs of water exposure or ingress, especially after heavy rainfall. Relocate the unit if necessary to a more protected area.
7. Troubleshooting
If your Mr Beams MBN350 spotlight is not functioning as expected, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Spotlight does not turn on. | Dead or incorrectly installed batteries. | Replace batteries, ensuring correct polarity. |
| Insufficient darkness (light sensor active). | Test in complete darkness. Ensure the light sensor is not obstructed. | |
| Motion sensor obstructed or out of range. | Clear any obstructions from the sensor. Ensure motion occurs within 15-30 feet. | |
| Spotlights are not synchronizing. | Units are on different network channels. | Verify all units are set to the same network channel (refer to product-specific channel setting instructions). |
| Units are out of wireless range. | Ensure units are within 150 feet of each other. Relocate units closer if necessary. | |
| Spotlight turns on continuously or randomly. | Motion sensor detecting unwanted movement (e.g., trees, animals). | Adjust the spotlight's angle or relocate it to minimize false triggers. |
| Environmental factors (e.g., strong winds, temperature changes). | Consider relocating the unit if environmental factors are consistently causing false triggers. |
8. Specifications
| Feature | Specification |
|---|---|
| Brand | Mr Beams |
| Model Number | MBN350 |
| Brightness | 200 Lumens |
| Light Source | LED (Non-Replaceable) |
| Power Source | Battery Powered |
| Batteries Required | 3 D-Cell Batteries (not included) |
| Motion Sensor Range | 15-30 feet |
| Connectivity Range (NetBright) | Up to 150 feet between units |
| Max Networked Units | Up to 50 spotlights |
| Material | Plastic |
| Color | Brown |
| Item Dimensions (L x W x H) | 6.88"L x 6.88"W x 5.11"H |
| Item Weight | 0.24 Kilograms |
| Water Resistance Level | Not Water Resistant |
| Installation Type | Flush Mount / Wall Mount |
9. Warranty and Support
9.1. Manufacturer's Warranty
The Mr Beams MBN350 Networked LED Wireless Motion Sensing Spotlight System comes with a 1-year limited warranty from the manufacturer. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
9.2. Customer Support
For technical assistance, troubleshooting not covered in this manual, or warranty inquiries, please contact Mr Beams customer support. Contact information can typically be found on the manufacturer's website or on the product packaging.