1. Introduction
Thank you for choosing the AstralPool Ultra 125 Robotic Pool Cleaner. This advanced automatic cleaner is designed to efficiently clean the bottom, walls, and waterline of public swimming pools up to 15 meters in length. Featuring a Gyro intelligent navigation system and powerful brushless DC motors, the Ultra 125 ensures thorough cleaning and superior performance. Please read this manual carefully before operating your device to ensure proper use and maintenance.
Figure 1: AstralPool Ultra 125 Robotic Pool Cleaner. This image shows the compact design of the cleaner, ready for deployment in a pool.
2. Setup
Follow these steps to prepare your AstralPool Ultra 125 for its first use.
- Unpacking: Carefully remove the cleaner and all accessories from the packaging. Ensure all components are present: the cleaner unit, power supply unit, and cable.
- Power Supply Placement: Place the power supply unit at least 3.5 meters (11.5 feet) from the edge of the pool. Ensure it is in a shaded area and protected from direct sunlight and splashing water. Do not immerse the power supply unit in water.
- Cable Connection: Connect the floating cable from the cleaner to the power supply unit. Ensure the connection is secure.
- Placing the Cleaner in the Pool: Gently lower the cleaner into the pool. Hold the handle and allow it to sink to the bottom. Ensure there are no air bubbles trapped inside the cleaner. The cleaner will sink naturally.
- Power On: Plug the power supply unit into a grounded electrical outlet.
Figure 2: Proper placement of the cleaner into the pool. Lower the unit gently to avoid tangling the cable.
3. Operating Instructions
The AstralPool Ultra 125 is designed for simple operation.
- Starting a Cleaning Cycle: Once the cleaner is in the pool and the power supply is connected, press the ON/OFF button on the power supply unit. The cleaner will begin its cleaning cycle automatically.
- Cleaning Cycle: The cleaner operates on a fixed 3-hour cleaning cycle, during which it systematically cleans the pool floor, walls, and waterline. The Gyro intelligent navigation system optimizes the cleaning path for maximum coverage and efficiency.
- Monitoring Operation: Observe the cleaner's movement. It should move across the pool surfaces, climbing walls to clean the waterline.
- Cycle Completion: After approximately 3 hours, the cleaner will automatically shut off.
- Removing the Cleaner: Disconnect the power supply from the electrical outlet. Gently pull the floating cable to bring the cleaner to the surface. Use the handle to lift the cleaner out of the water. Allow excess water to drain from the cleaner before placing it on the pool deck. Do not pull the cleaner out of the water by its cable.
4. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your AstralPool Ultra 125.
- Cleaning the Filter Bag: After each cleaning cycle, or as needed, remove and clean the ultrafine filter bag.
- Open the cleaner's filter compartment (refer to your cleaner's specific design for access).
- Remove the filter bag.
- Rinse the filter bag thoroughly with a garden hose until all debris is removed.
- Ensure the filter bag is completely clean before reinserting it into the cleaner. A clogged filter will reduce cleaning efficiency.
- Cable Inspection: Periodically inspect the 23-meter floating cable for any signs of damage, kinks, or wear. If damage is found, contact authorized service personnel.
- Impeller Check: Occasionally check the impeller for any trapped debris that might obstruct water flow.
- Storage: When not in use for extended periods, clean the cleaner thoroughly, ensure the filter bag is dry, and store the unit in a cool, dry, shaded area, away from direct sunlight and extreme temperatures.
Figure 3: Illustrative image of filter bag cleaning. Regular cleaning of the ultrafine filter bag is crucial for maintaining suction power.
5. Troubleshooting
This section addresses common issues you might encounter with your AstralPool Ultra 125.
| Problem | Possible Cause | Solution |
|---|---|---|
| Cleaner does not move or start. |
|
|
| Poor cleaning performance or missed areas. |
|
|
| Cleaner does not climb walls or clean waterline effectively. |
|
|
| Cable tangles during operation. |
|
|
6. Specifications
| Feature | Detail |
|---|---|
| Model | Ultra 125 |
| Brand | Astrapool |
| Pool Type | Public pools |
| Maximum Pool Length | 15 meters |
| Cleaning Coverage | Floor, Walls, Waterline |
| Cleaning Cycle Duration | 3 hours |
| Cable Length | 23 meters |
| Motor Type | Brushless DC (1 pump motor, 1 traction motor) |
| Pump Suction Flow | 16.4 m³/h |
| Navigation System | Gyro Intelligent Navigation |
| Filter Type | Ultrafine Bag Filter |
| Package Dimensions | 54.5 x 51 x 37.7 cm |
| Package Weight | 14.11 kg |
| Manufacturer Reference | 60165 |
| ASIN | B00WRCTZPK |
7. Warranty and Support
For information regarding the product warranty, please refer to the warranty card included with your purchase or visit the official Astrapool website. For technical support, spare parts, or service inquiries, please contact your authorized Astrapool dealer or customer service department. Keep your purchase receipt as proof of purchase for warranty claims.