ELK Lighting Ventor 17181/2 Two-Light Bath Vanity Installation and User Manual

1. Important Safety Information

Please read and understand all instructions before beginning installation. Failure to do so may result in electric shock, fire, or other injuries that could be hazardous or even fatal. Keep these instructions for future reference.

• WARNING: Risk of electric shock. Disconnect power at the circuit breaker or fuse box before installation or servicing.
• All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
• This product is designed for indoor use only.
• Do not install this fixture in wet locations unless specifically rated for such use.
• Use only the specified bulb type and wattage. Exceeding the maximum wattage may cause overheating and damage the fixture. (Lamp Type: G9, Max Wattage: 40 Watts per bulb).
• Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Wash hands after handling.

2. Package Contents

Carefully unpack the fixture and check that all parts are included. If any parts are missing or damaged, do not attempt to assemble or install the product. Contact customer service for replacement parts.

• Fixture Body (1)
• Glass Shades (2)
• Mounting Hardware Kit (1) - Typically includes mounting screws, wire nuts, and a mounting plate.
• Instruction Manual (1)

Image 1: ELK Lighting Ventor 17181/2 Two-Light Bath Vanity. This image displays the complete vanity light fixture with its polished chrome backplate and two glass shades.

3. Setup and Installation

Before you begin, ensure the power is turned off at the circuit breaker. Gather the necessary tools: screwdriver, wire strippers, electrical tape, and safety glasses.

1. Turn Off Power: Locate the circuit breaker that supplies power to the light fixture outlet box. Turn the breaker to the "OFF" position. Verify power is off using a voltage tester.
2. Remove Old Fixture (if applicable): Carefully disconnect and remove any existing light fixture.
3. Attach Mounting Plate: Secure the mounting plate (typically included in the hardware kit) to the electrical outlet box using the provided screws. Ensure it is firmly attached.

   (Image description: A diagram showing the mounting plate being attached to a standard electrical junction box with screws.)

4. Make Electrical Connections:
   • Connect the green or bare copper ground wire from the fixture to the ground wire from the outlet box (usually bare copper or green). Secure with a wire nut.
   • Connect the white wire from the fixture to the white (neutral) wire from the outlet box. Secure with a wire nut.
   • Connect the black wire from the fixture to the black (hot) wire from the outlet box. Secure with a wire nut.
   • Ensure all wire connections are secure and wrapped with electrical tape if necessary. Carefully tuck all wires into the outlet box.

     (Image description: A close-up diagram illustrating the proper wire connections: ground to ground, white to white, black to black, secured with wire nuts.)
5. Mount Fixture Body: Align the fixture's backplate (dimensions: 16.00" width x 5.00" length) with the mounting plate and secure it with the provided screws. Ensure the fixture is flush against the wall and stable.

   (Image description: A view of the fixture's backplate being attached to the mounting plate, showing the screws being tightened.)

6. Install Bulbs: Insert two G9 base bulbs (maximum 40 watts each, not included) into the sockets. Do not overtighten.
7. Attach Glass Shades: Carefully place the glass shades over the bulb sockets and secure them according to the fixture's design (e.g., with retaining rings or screws). Ensure they are snug but do not overtighten.

   (Image description: A step-by-step illustration showing how to install the G9 bulbs and then secure the glass shades onto the fixture.)

8. Restore Power: Once installation is complete, return to the circuit breaker and turn the power back "ON". Test the fixture.

4. Operating Instructions

The ELK Lighting Ventor Bath Vanity is operated by a standard wall switch connected to the electrical circuit. Simply toggle the wall switch to turn the light fixture ON or OFF.

• Ensure the wall switch is in the "ON" position for the fixture to receive power.
• If the fixture does not turn on, refer to the Troubleshooting section.

5. Maintenance

Regular maintenance will help preserve the appearance and functionality of your light fixture.

• Cleaning: Always disconnect power at the circuit breaker before cleaning. To clean the polished chrome finish, use a soft, dry or slightly damp cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
• Glass Shades: The glass shades can be removed for thorough cleaning. Wash with mild soap and water, rinse thoroughly, and dry completely before reattaching.
• Bulb Replacement: Ensure power is off before replacing bulbs. Allow bulbs to cool completely before touching. Replace with G9 base bulbs, maximum 40 watts.

6. Troubleshooting

If your fixture is not functioning correctly, consult the following troubleshooting guide:

If the problem persists after attempting these solutions, contact a qualified electrician or ELK Lighting customer support.

7. Specifications

8. Warranty and Support

This ELK Lighting product comes with a manufacturer's warranty. For specific warranty details, including coverage and duration, please refer to the documentation provided with your purchase or visit the official ELK Lighting website.

For technical assistance, missing parts, or warranty claims, please contact ELK Lighting customer support directly. Have your model number (17181/2) and proof of purchase ready when contacting support.

ELK Lighting Contact Information:

• Please refer to the ELK Lighting official website or product packaging for the most current contact details.