1. Product Overview
This manual provides instructions for the Westinghouse 3W 120V Flicker Flame Decorative Bulb, model 3CA8/FLK/CB. This incandescent bulb features a CA8 size and shape with an E12 candelabra base, designed to produce a decorative flicker flame effect with an orange light output. It operates at 3 Watts and 120 Volts, suitable for lower light level applications.
- Bulb Type: Incandescent
- Base Type: E12 Candelabra
- Wattage: 3 Watts
- Voltage: 120 Volts
- Special Feature: Flicker Flame effect, Dimmable
- Light Color: Orange
- Estimated Life: Approximately 1.4 years based on 3 hours of daily use (3000 hours total average life)
2. Safety Information
Please read and understand all safety instructions before installing or using this product. Failure to follow these instructions may result in electric shock, fire, or other hazards.
- Power Off: Always turn off the power to the fixture at the circuit breaker or fuse box before installing, removing, or inspecting the bulb.
- Cool Down: Allow the bulb to cool completely before handling. Hot bulbs can cause burns.
- Proper Fixture: Use this bulb only in fixtures rated for the specified wattage and voltage (3W, 120V).
- Dry Location: This bulb is rated for outdoor usage, but ensure the fixture itself is suitable for the environment and protected from direct water exposure if used outdoors.
- Disposal: Dispose of used bulbs according to local regulations.
- Dimmable: This bulb is dimmable. Ensure your dimmer switch is compatible with incandescent bulbs.
3. Setup and Installation
Follow these steps to properly install your Westinghouse Flicker Flame Decorative Bulb:
- Ensure Power is Off: Before beginning installation, verify that the power supply to the light fixture is turned off at the circuit breaker or wall switch.
- Remove Old Bulb (if applicable): If replacing an existing bulb, carefully unscrew it from the socket. Allow it to cool if it was recently in use.
- Inspect Fixture: Check the light fixture's socket for any damage or debris. Ensure it is clean and dry.
- Screw in New Bulb: Gently screw the Westinghouse Flicker Flame Decorative Bulb into the E12 candelabra base socket. Turn clockwise until it is finger-tight. Do not overtighten.
- Restore Power: Once the bulb is securely installed, restore power to the fixture at the circuit breaker or wall switch.
- Test: Turn on the light switch to confirm the bulb is functioning correctly and producing the flicker flame effect.
Image 1: Side view of the Westinghouse Flicker Flame Decorative Bulb, showing the clear glass and internal flicker element.
Image 2: Close-up view of the E12 candelabra screw base of the Westinghouse Flicker Flame Decorative Bulb.
4. Operating Instructions
Operating this decorative bulb is straightforward:
- Standard Operation: Simply use the wall switch or fixture switch to turn the light on or off.
- Dimming Function: If installed in a compatible dimmable fixture with an appropriate dimmer switch, you can adjust the brightness of the flicker flame effect to your desired level.
- Flicker Effect: The bulb is designed to simulate a flickering candle flame, providing a warm, ambient orange light.
5. Maintenance
Minimal maintenance is required for this bulb:
- Cleaning: To clean the bulb, ensure the power is off and the bulb is cool. Gently wipe with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
- Replacement: When the bulb reaches the end of its operational life, it will cease to illuminate. Follow the installation steps (Section 3) to replace it with a new, compatible bulb.
6. Troubleshooting
If your Westinghouse Flicker Flame Decorative Bulb is not functioning as expected, consider the following:
| Problem | Possible Cause | Solution |
|---|---|---|
| Bulb does not light up. |
|
|
| Flicker effect is inconsistent or absent. |
|
|
7. Specifications
Detailed specifications for the Westinghouse 3W 120V Flicker Flame Decorative Bulb:
| Brand | Westinghouse |
| Model Number | 3CA8/FLK/CB |
| Light Type | Incandescent |
| Wattage | 3 Watts |
| Voltage | 120 Volts (Accepted voltage frequency: 100 to 120 Volts and 60 Hertz) |
| Bulb Shape Size | CA8 |
| Bulb Base | E12 Candelabra |
| Special Feature | Dimmable, Flicker Flame Effect |
| Light Color | Orange |
| Brightness | 3 Lumens |
| Average Life | 3000 Hours |
| Material | Copper (base) |
| Indoor/Outdoor Usage | Outdoor (ensure fixture is suitable) |
| Item Weight | 0.387 ounces |
| Package Dimensions | 4.02 x 1.18 x 1.18 inches |
| UPC | 030721036569 |
8. Warranty and Support
For warranty information or technical support regarding your Westinghouse Flicker Flame Decorative Bulb, please refer to the official Westinghouse website or contact their customer service department. Keep your purchase receipt for warranty claims.
Westinghouse Customer Support: Please visit the Westinghouse Store on Amazon or the official Westinghouse website for contact details and further assistance.
