Moen DN6893BN 3-Piece Decorative Bath Hardware Set Instruction Manual

Introduction

Thank you for choosing the Moen Sage Collection 3-Piece Decorative Bath Hardware Set. This set is crafted from durable metal with a Brushed Nickel finish, offering both functionality and a timeless aesthetic to your bathroom. Please read these instructions carefully before installation and use to ensure proper function and longevity of your product.

Image: The complete Moen Sage 3-Piece Decorative Bath Hardware Set, featuring a towel bar, towel ring, and toilet paper holder, all in a brushed nickel finish, mounted on a bathroom wall.

Setup and Installation

This hardware set is designed for wall-mount installation. Ensure you have the necessary tools before beginning. Tools typically include a drill, screwdriver, measuring tape, and level.

General Installation Steps:

1. Prepare the Wall: Choose the desired location for each piece. Use a level to mark the mounting points accurately. For secure installation, it is recommended to mount into wall studs. If studs are not available, use appropriate wall anchors (included with the hardware kit).
2. Mount the Brackets: Attach the mounting brackets to the wall using the provided screws. Ensure they are firmly secured and level.
3. Attach the Hardware: Slide the decorative base of each hardware piece over its corresponding mounting bracket. Secure the piece in place using the small set screw, typically located on the underside of the base.

Specific Component Installation Notes:

Towel Bar

Image: A close-up view of the Moen Sage towel bar, highlighting its brushed nickel finish and design details.

The towel bar requires two mounting points. Ensure both brackets are installed at the same height and distance apart to support the bar evenly.

Towel Ring

Image: A detailed view of the Moen Sage towel ring, showcasing its circular design and brushed nickel finish.

The towel ring mounts with a single bracket. Position it conveniently for hand towels near a sink.

Toilet Paper Holder

Image: A close-up of the Moen Sage toilet paper holder, featuring its brushed nickel finish and functional design.

The toilet paper holder also uses two mounting points. The design allows for easy roll replacement by pivoting one arm upwards.

Image: A diagram illustrating the pivoting mechanism of the toilet paper holder for convenient roll changes.

Operating Instructions

Each piece in the Moen Sage Collection is designed for straightforward use.

• Towel Bar: Hang bath towels or larger hand towels over the bar. The 18-inch length is suitable for various towel sizes.
• Towel Ring: Ideal for hand towels. Simply drape the towel through the ring for easy access.
• Toilet Paper Holder: To replace a roll, gently lift one of the arms of the holder. The arm will pivot upwards, allowing you to slide the old roll off and a new roll on. Lower the arm back into place to secure the new roll.

Care and Maintenance

To maintain the Brushed Nickel finish and ensure the longevity of your Moen bath hardware, follow these simple cleaning guidelines:

• Regular Cleaning: Clean with a soft, damp cloth. Mild soap can be used if necessary.
• Avoid Harsh Cleaners: Do not use abrasive cleaners, harsh chemicals, or polishes that could damage the finish. Products containing ammonia, bleach, or alcohol are not recommended.
• Drying: After cleaning, wipe the hardware dry with a soft cloth to prevent water spots and maintain its luster.

Troubleshooting

Most issues with bath hardware are related to installation or general wear. Here are some common points:

• Loose Hardware: If any piece becomes loose, check the set screw on the underside of the base. Tighten it gently with a small hex key or screwdriver. Avoid over-tightening.
• Scratches or Finish Damage: Minor scuffs may be buffed out with a very fine, non-abrasive polishing cloth. For significant damage, contact Moen customer support.
• Difficulty with Toilet Paper Roll Replacement: Ensure the pivoting arm is fully lifted before attempting to remove or install a new roll. Do not force the mechanism.

Specifications

Warranty Information

This Moen product is backed by Moen’s Limited Lifetime Warranty. For detailed information regarding warranty coverage, terms, and conditions, please refer to the official Moen website or contact customer support.

The warranty covers defects in material and manufacturing under normal use and service.

Customer Support

For further assistance, technical support, or to inquire about replacement parts, please visit the official Moen website or contact their customer service department. Contact information can typically be found on the product packaging or the manufacturer's website.

Online resources may include installation videos, FAQs, and product registration.