Introduction
This manual provides detailed instructions for the safe and efficient use of your Commercial Electric 2.99 in. LED White Battery Operated Puck Light (3-Pack). Please read this manual thoroughly before installation and operation, and retain it for future reference.
Important Safety Information
- Always ensure batteries are inserted with correct polarity (+/-).
- Do not mix old and new batteries, or different types of batteries.
- Remove batteries if the product is not used for an extended period.
- Keep batteries out of reach of children.
- Do not expose the lights to excessive moisture or extreme temperatures.
- This product is designed for indoor use only.
Package Contents
Verify that all components are present before beginning installation.
- 3 x LED Puck Lights
- 1 x Remote Control
- Mounting Hardware (e.g., adhesive pads or screws, depending on model variation)
Image: Three LED puck lights, as included in the 3-pack.
Setup and Installation
1. Battery Installation
- Gently twist the back cover of each puck light counter-clockwise to open the battery compartment.
- Insert three (3) AAA batteries into each puck light, observing the polarity markings (+/-). (Total 9 AAA batteries required for 3 lights).
- Replace the back cover by aligning it and twisting clockwise until secure.
- For the remote control, slide open the battery compartment cover and insert the required battery (typically a CR2025 coin cell, check remote for specific type), observing polarity.
Image: A single LED puck light, showing its design and indicating where the battery compartment is located on the back.
2. Mounting the Puck Lights
The puck lights can be mounted using adhesive pads or screws, depending on your preference and the included hardware.
- Using Adhesive Pads:
- Clean the desired mounting surface thoroughly to ensure it is free of dust and grease.
- Peel the protective backing from one side of the adhesive pad and firmly attach it to the back of the puck light.
- Peel the remaining backing from the adhesive pad and press the puck light firmly onto the mounting surface for at least 30 seconds.
- Using Screws (if applicable):
- Mark the desired mounting location.
- Use the provided screws to secure the mounting bracket (if separate) or the light itself to the surface.
Image: Three LED puck lights illuminating a kitchen countertop from under cabinets, demonstrating a typical installation.
Operation
The Commercial Electric Puck Lights are operated using the included remote control.
- Power On/Off: Press the 'ON' button to turn the lights on, and the 'OFF' button to turn them off.
- Brightness Adjustment: Use the brightness buttons (often '+' and '-' or specific dimming levels) on the remote to adjust the light intensity.
- Timer Function: Some models may include a timer function (e.g., 30 min, 60 min). Refer to your remote for specific options.
Maintenance
Battery Replacement
When the lights begin to dim or the remote control range decreases, it is time to replace the batteries. Follow the battery installation steps outlined in the 'Setup and Installation' section.
Cleaning
To clean the puck lights, gently wipe the surface with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or electronic components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lights do not turn on. | Dead or incorrectly inserted batteries. | Check battery polarity and replace with fresh AAA batteries. |
| Remote control not working. | Remote battery is dead or incorrectly inserted. Obstruction between remote and lights. | Replace remote battery. Ensure clear line of sight to the lights. |
| Lights are dim. | Low battery power. | Replace all AAA batteries in the puck lights. |
| Lights flicker. | Low battery power. Loose battery connection. | Replace batteries. Ensure batteries are seated firmly. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Commercial Electric |
| Model Number | BA002 WH |
| Light Source Type | LED |
| Light Color | White |
| Power Source | Battery Powered |
| Batteries Required | 3 x AAA per puck light (9 AAA total for 3-pack) |
| Control Method | Remote Control |
| Product Dimensions | 2.99 x 2.99 x 0.99 inches (per puck light) |
| Mounting Type | Wall Mount (Adhesive/Screw) |
| Specific Uses | Cabinet, Indoor |
Warranty and Support
Commercial Electric products are manufactured to high-quality standards. For specific warranty information or technical support, please refer to the product packaging or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.