PRASTEL TC4E Original Gate Remote Control User Manual

1. Introduction

This manual provides comprehensive instructions for the PRASTEL TC4E Original Gate Remote Control. The TC4E is a robust and compact remote designed for controlling gate systems operating at 433.92 MHz. It features a durable aluminum and ABS construction, ensuring longevity and resistance to damage. This model is a direct replacement for several older PRASTEL rolling code remotes.

Important Note: Be aware of similar-looking models from other manufacturers that may not offer the same compatibility or quality as the original PRASTEL TC4E. The authentic PRASTEL remote can be identified by its dark rubber buttons or silver keys with symbols, and the PRASTEL brand mark on the back.

2. Product Overview

Figure 1: Front view of the PRASTEL TC4E Gate Remote Control, showing its compact design and four buttons.

Key Features:

• Frequency: 433.92 MHz rolling code.
• Construction: Durable aluminum and ABS casing with an integrated key hook.
• Buttons: 4 programmable buttons.
• Battery: CR2032 button cell (included).
• Dimensions: Approximately 32 mm × 52 mm × 12 mm.
• Range: Up to 10 meters (depending on environmental factors and receiver).
• Compatibility: Replaces EXTEL ATEM80001, PRASTEL BFOR, PRASTEL MPSTF2RE, PRASTEL MPSTF4RE, PRASTEL MPSTL-1E, PRASTEL MPSTL-2E, PRASTEL MPSTL-4E, PRASTEL MPSTP2E, PRASTEL MT2E, PRASTEL MT4E, PRASTEL SLIM 2E, PRASTEL 4E, PRASTEL TC2E, PRASTEL TRQ2P, PRASTEL TRQ4P.

3. Setup and Programming

The PRASTEL TC4E remote control uses a "registration in the receiver" programming method. The exact procedure may vary slightly depending on your specific gate receiver model. Always refer to your gate system's receiver manual for detailed programming instructions.

General Programming Steps (Consult your receiver manual for specifics):

1. Access the Receiver: Locate your gate system's receiver unit. This is typically found near the gate motor or control panel.
2. Activate Programming Mode: Press and hold the programming button (often labeled 'P' or 'PROG') on your receiver board. The indicator light on the receiver should change, indicating it is in programming mode.
3. Transmit from New Remote: While the receiver is in programming mode, press and hold the desired button on your new PRASTEL TC4E remote control. Hold the button until the receiver's indicator light confirms successful registration (e.g., flashes, changes color, or turns off).
4. Exit Programming Mode: Some receivers automatically exit programming mode after a short period of inactivity. Others may require a second press of the programming button or a specific sequence.
5. Test the Remote: After programming, move away from the receiver and test the remote control to ensure it operates the gate correctly.

If your receiver does not have an accessible programming button, it might support remote programming. In such cases, you may need to use an existing, already programmed remote to transfer the code to the new TC4E remote. Refer to your receiver's manual for "remote programming" or "master remote" instructions.

4. Operating Instructions

Once programmed, operating the PRASTEL TC4E remote control is straightforward:

• Opening/Closing the Gate: Press the programmed button on the remote control once to activate the gate. Depending on your gate system's configuration, a single press may open, close, or stop the gate.
• Stopping the Gate: If your gate is in motion, pressing the same programmed button again may stop its movement.
• Multiple Functions: If you have programmed multiple buttons for different functions (e.g., opening a pedestrian gate, controlling lights), press the corresponding button for the desired action.

Ensure you are within the operational range (up to 10 meters) of your gate receiver for reliable operation. Obstructions and environmental interference can affect the remote's range.

5. Maintenance

Battery Replacement:

The PRASTEL TC4E remote control is powered by a CR2032 button cell battery. When the remote's range decreases significantly or it stops responding, it is likely time to replace the battery.

1. Open the Casing: Carefully open the remote control casing. This usually involves gently prying apart the two halves using a small flat-head screwdriver or a similar tool at the seam.
2. Remove Old Battery: Locate the CR2032 battery. Note its orientation (positive (+) side up or down). Gently remove the old battery.
3. Insert New Battery: Insert a new CR2032 battery, ensuring it is placed in the correct orientation.
4. Close the Casing: Carefully snap the two halves of the remote control casing back together until it is securely closed.
5. Test Functionality: Test the remote control to ensure it is working correctly after battery replacement.

Disposal: Dispose of old batteries responsibly according to local regulations.

6. Troubleshooting

7. Specifications

8. Warranty and Support

The PRASTEL TC4E remote control comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or normal wear and tear.

For technical support, warranty claims, or further assistance, please contact your PRASTEL retailer or visit the official PRASTEL website. Please have your purchase receipt and product model number (TC4E) available when contacting support.