WORX WG154 20V Cordless String Trimmer & Edger User Manual

Important Safety Information

Always wear appropriate personal protective equipment (PPE), such as safety glasses or a face shield, hearing protection, and sturdy, non-slip boots. Be mindful of the rotating cutting line and flying debris, and ensure a clear area around you before starting the trimmer.

Read and understand all instructions before operating the tool. Keep children and bystanders away while operating. Do not operate in wet conditions. Disconnect the battery before performing any maintenance or adjustments.

Product Overview

The WORX WG154 20V String Trimmer and Edger is a versatile 2-in-1 tool designed for efficient lawn care. It easily converts from a string trimmer to a precision edger, offering convenience and saving space. This cordless tool is powered by a 20V MaxLithium battery, part of the WORX Power Share family, allowing battery interchangeability with other WORX tools.

Figure 1: WORX WG154 20V Trimmer & Edger and Included Components

Key Features:

• 2-in-1 Functionality: Easily converts from a string trimmer to a lawn edger.
• Rotating Head: The head rotates 180 degrees for quick conversion between trimming and edging modes.
• Lightweight Design: Weighing only 4.2 lbs (3.2 lbs without battery), it is designed for easy handling.
• Automatic Line Feed: Ensures continuous cutting without manual adjustments.
• Flower Guard: An adjustable spacer guard protects plants and delicate landscaping.
• Power Share Compatibility: Uses the same 20V MaxLithium battery that powers over 75+ WORX tools.

Setup and Assembly

The WORX WG154 requires minimal assembly. Follow these steps to prepare your trimmer for use:

1. Attach the Safety Guard: Secure the safety guard to the trimmer head using the provided screw. Ensure it is firmly attached to prevent debris from striking the user.
2. Install the Battery: Insert the fully charged 20V MaxLithium battery into the battery port on the handle until it clicks into place.
3. Adjust the Handle: Loosen the adjustment knob on the auxiliary handle and slide it to a comfortable position for optimal balance and control. Tighten the knob securely.
4. Adjust the Shaft Length: If applicable, adjust the telescopic shaft to your preferred working height by loosening the collar, extending or retracting the shaft, and then tightening the collar.

Figure 2: Assembled WORX WG154 Trimmer

Operating Instructions

Starting and Stopping:

• To start the trimmer, press the safety lock-off button and then squeeze the trigger switch.
• To stop, release the trigger switch.

Converting from Trimmer to Edger:

The WG154 features a rotating head for easy conversion:

1. Ensure the tool is off and the battery is removed.
2. Grasp the trimmer head and pull it away from the shaft.
3. Rotate the head 180 degrees until it locks into the edging position.
4. Re-insert the battery and you are ready to edge.

Figure 3: Converting Trimmer to Edger

Automatic Line Feed:

The trimmer is equipped with an automatic line feed system. When you start the trimmer, a small amount of line is automatically fed out. If the line becomes too short, simply release the trigger and press it again to advance more line. Avoid manually pulling the line during operation.

Figure 4: Automatic Line Feed System

Using the Flower Guard:

The adjustable spacer guard helps prevent accidental trimming of delicate plants, flowers, and other garden decorations. Position the guard between the cutting line and the objects you wish to protect.

Figure 5: Using the Flower Guard

Maintenance

Cleaning:

• After each use, disconnect the battery and clean the trimmer head and guard with a damp cloth.
• Remove any grass clippings or debris from the air vents to ensure proper motor cooling.
• Do not use harsh chemicals or abrasive cleaners.

Spool Replacement:

When the trimmer line runs out, you will need to replace the spool. The part number for the replacement spool is WA0010. WORX offers "free spools for life," though shipping costs apply. Alternatively, replacement spools can be purchased from various retailers, including Amazon.

1. Ensure the trimmer is off and the battery is removed.
2. Press the tabs on the side of the spool cap and remove it.
3. Remove the empty spool.
4. Insert a new pre-wound spool, ensuring the line is threaded through the eyelet on the spool cap.
5. Align the spool cap and snap it back into place.
6. Pull a small amount of line manually to ensure it is not stuck.

Battery Care:

• Always use the WORX 20V battery charger provided.
• Store batteries in a cool, dry place away from direct sunlight and extreme temperatures.
• Do not store batteries in a discharged state for extended periods.
• If the battery is not used for a long time, charge it periodically to maintain its life.

Troubleshooting

Specifications

Warranty Information

WORX provides a limited warranty for its products. For the WG154 String Trimmer and Edger:

• Tool: 3 Years Limited Warranty
• Battery: 2 Years Limited Warranty

Please retain your proof of purchase for warranty claims. For detailed warranty terms and conditions, refer to the official WORX website or contact customer support.

Figure 6: WORX Warranty Details

Customer Support

For further assistance, technical support, or to inquire about replacement parts, please visit the official WORX website or contact their customer service department.

WORX Official Website: www.worx.com
WORX Amazon Store: Visit the WORX Store on Amazon