National Hardware N199-190
National Hardware V162 Clothes Hook Instruction Manual
Model: N199-190
Introduction
This manual provides detailed instructions for the installation, use, and maintenance of your National Hardware V162 Clothes Hook. Designed for durability and functionality, this nickel-finished zinc hook is suitable for various wall-mounting applications, offering a reliable solution for hanging items up to 35 lbs.
Safety Information
- Always wear appropriate safety gear, such as eye protection, when drilling or using tools.
- Ensure the mounting surface is structurally sound and can support the hook's weight capacity plus the weight of items to be hung.
- Do not exceed the maximum weight capacity of 35 lbs to prevent damage to the hook or mounting surface.
- Keep small parts and screws out of reach of children.
Package Contents
Verify that all components are present before beginning installation:
- V162 Clothes Hook (2 per package)
- #6 Flat Head Screws (4 per hook, total 8 for 2-pack)
Image: A single National Hardware V162 Clothes Hook, showcasing its nickel finish, oval mounting plate with two screw holes, and a curved hook ending in a spherical tip. This image represents one of the two hooks included in the package.
Setup and Installation
Follow these steps for proper installation of your clothes hook:
Tools Required:
- Pencil
- Drill
- Drill bit (appropriate size for #6 screws and wall anchors, if needed)
- Screwdriver (Phillips head recommended)
- Level (optional, for precise alignment)
Installation Steps:
- Select Location: Choose a suitable location on a wall or surface that can support the hook and its intended load. Consider height and accessibility.
- Mark Pilot Holes: Hold the hook against the desired mounting surface. Using a pencil, mark the two mounting hole locations. The mounting holes have a diameter of 0.14 inches.
- Drill Pilot Holes: Using a drill with an appropriately sized drill bit (slightly smaller than the screw diameter), carefully drill pilot holes at the marked locations. If mounting into drywall without a stud, consider using wall anchors (not included) for added stability.
- Attach Hook: Align the hook's mounting holes with the drilled pilot holes. Insert the provided #6 flat head screws into the holes.
- Secure Hook: Using a screwdriver, tighten the screws until the hook is firmly secured to the surface. Do not overtighten, as this may strip the screws or damage the hook/surface.
- Test Stability: Gently pull on the hook to ensure it is securely mounted before hanging any items.
Operation and Usage
The National Hardware V162 Clothes Hook is designed for simple and effective use. Once securely mounted, it can be used to hang a variety of items.
- Weight Capacity: The hook has a maximum weight capacity of 35 pounds. Ensure that the total weight of items hung on the hook does not exceed this limit.
- Intended Use: Ideal for hanging coats, hats, towels, bags, and other lightweight to medium-weight items in closets, entryways, bathrooms, or utility areas.
- Placement: Distribute weight evenly if hanging multiple items. Avoid hanging sharp or abrasive objects that could scratch the hook's finish.
Maintenance
To ensure the longevity and appearance of your National Hardware V162 Clothes Hook, follow these simple maintenance guidelines:
- Cleaning: Wipe the hook periodically with a soft, damp cloth to remove dust and dirt. For stubborn marks, a mild soap solution can be used, followed by drying with a clean, soft cloth.
- Avoid Harsh Cleaners: Do not use abrasive cleaners, solvents, or chemical polishes, as these can damage the nickel finish.
- Inspect Periodically: Occasionally check the mounting screws to ensure they remain tight. Retighten if necessary to maintain stability.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Hook feels loose after installation. | Screws are not fully tightened, or mounting surface is not strong enough. | Retighten screws. If still loose, consider using wall anchors or mounting to a stud/more secure surface. |
| Hook finish appears dull or scratched. | Accumulation of dirt, use of abrasive cleaners, or contact with sharp objects. | Clean with a soft, damp cloth. Avoid abrasive materials. |
| Items slide off the hook easily. | Items are too wide or have slippery material. | Ensure items are appropriately sized for the hook. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | N199-190 |
| Brand | National Hardware |
| Material | Zinc |
| Finish Type | Nickel |
| Weight Capacity | 35 lbs (15.88 kg) |
| Number of Hooks | 1 (per unit, sold as 2/pk) |
| Mounting Type | Wall Mounting |
| Mounting Hole Diameter | 0.14 in (3.56 mm) |
| Projection | 1-15/32 in (approx. 3.73 cm) |
| Dimensions (H x W) | 1-11/16 in H x 1 in W (approx. 4.29 cm H x 2.54 cm W) |
| Included Hardware | (4) #6 Flat Head Screws (per hook) |
Support and Warranty
For product support, technical assistance, or warranty information, please contact National Hardware customer service. Refer to the product packaging or the official National Hardware website for the most current contact details.
National Hardware products are manufactured to high-quality standards. Please retain your proof of purchase for any warranty claims.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.