Introduction
The GoControl WO15Z-1 is a Z-Wave enabled single wall outlet designed to integrate into your smart home system. It allows for remote control of connected devices via a Z-Wave certified gateway, in addition to local manual control. This outlet also functions as a Z-Wave repeater, extending the range and reliability of your Z-Wave network.
This manual provides essential information for the safe installation, operation, and maintenance of your GoControl WO15Z-1 Z-Wave Single Wall Outlet.
Figure 1: Front view of the GoControl WO15Z-1 Z-Wave Single Wall Outlet.
Safety Information
- WARNING: Risk of Electric Shock. Installation involves high voltage wiring. Always turn off power at the circuit breaker or fuse box before installation, servicing, or removing the device.
- Installation should be performed by a qualified electrician or a person with a thorough understanding of electrical systems and safety.
- Ensure all wiring connections are secure and comply with national and local electrical codes, including NEC 2008 for tamper-resistant outlets.
- Do not use this device with appliances that could be dangerous if left unattended, such as heaters or irons.
- This device is intended for indoor use only.
- Operating temperature range: 32-104°F (0-40°C).
Package Contents
Verify that your package contains the following items:
- GoControl WO15Z-1 Z-Wave Single Wall Outlet
- White decorative switch plate
- Installation screws
Setup and Installation
1. Wiring the Outlet
- Turn off power: Locate the circuit breaker or fuse that controls the outlet you intend to replace and turn off the power. Verify the power is off using a voltage tester.
- Remove existing outlet: Carefully remove the wall plate and unscrew the existing outlet from the electrical box. Disconnect the wires, noting their connections (Line/Hot, Neutral, Ground).
- Connect the WO15Z-1: The GoControl WO15Z-1 requires a ground wire for proper operation. Connect the wires from the electrical box to the corresponding terminals on the WO15Z-1:
- Line (Hot) Wire: Connect to the terminal marked 'LINE'.
- Neutral Wire: Connect to the terminal marked 'NEUTRAL'.
- Ground Wire: Connect to the terminal marked 'GROUND'.
- Mount the outlet: Carefully fold the wires into the electrical box and secure the WO15Z-1 outlet with the provided screws. Attach the decorative switch plate.
- Restore power: Turn the power back on at the circuit breaker.
Figure 2: Back view of the GoControl WO15Z-1 showing wiring terminals.
2. Z-Wave Network Inclusion (Pairing)
To integrate the WO15Z-1 into your Z-Wave network, follow these steps:
- Ensure your Z-Wave gateway/controller is in inclusion (pairing) mode. Refer to your gateway's manual for specific instructions.
- Press the button on the front of the WO15Z-1 outlet once. The LED indicator will flash to confirm inclusion mode.
- Your Z-Wave gateway should confirm successful inclusion. The LED on the outlet will stop flashing and remain solid or turn off, depending on the network status.
- If inclusion is unsuccessful, refer to the Troubleshooting section or your gateway's manual.
3. Z-Wave Network Exclusion (Unpairing)
To remove the WO15Z-1 from your Z-Wave network:
- Ensure your Z-Wave gateway/controller is in exclusion (unpairing) mode.
- Press the button on the front of the WO15Z-1 outlet once.
- Your Z-Wave gateway should confirm successful exclusion.
Installation Video Guide
Watch this official video for a visual guide on installing and setting up your GoControl WO15Z-1 Z-Wave Single Wall Outlet.
Video 1: GoControl WO15Z-1 Z-Wave Single Wall Outlet Installation and Setup Guide. This video demonstrates the physical installation and Z-Wave pairing process for the outlet.
Operating Instructions
Manual Control
The GoControl WO15Z-1 features one controlled outlet (the bottom receptacle). You can manually toggle the power to this controlled outlet by pressing the button located on the front of the device. Press once to turn on, press again to turn off.
Z-Wave Control
Once successfully included in your Z-Wave network, you can control the connected device through your Z-Wave gateway or smart home application. This allows for remote on/off control, scheduling, and integration into scenes with other Z-Wave devices.
The WO15Z-1 also acts as a wireless repeater, strengthening your Z-Wave mesh network by forwarding commands to other devices that might be out of direct range of your controller.
Maintenance
- Cleaning: To clean the outlet, ensure power is off at the circuit breaker. Wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- No User-Serviceable Parts: There are no user-serviceable parts inside the WO15Z-1. Do not attempt to open or repair the device.
- Firmware Updates: Any firmware updates would typically be managed through your Z-Wave gateway, if supported. Refer to your gateway's documentation for details.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Outlet does not power on/off manually. | No power to the outlet; incorrect wiring. | Check circuit breaker. Verify wiring connections are secure and correct (Line, Neutral, Ground). |
| Cannot include (pair) the outlet with Z-Wave gateway. | Gateway not in inclusion mode; outlet too far from gateway; interference. | Ensure gateway is in inclusion mode. Move outlet closer to gateway temporarily. Try excluding the device first, then re-including. |
| Outlet loses Z-Wave connection after power interruption. | Temporary network disruption. | The outlet is designed to automatically reconnect to the Z-Wave network after a power interruption. Allow a few minutes for it to re-establish connection. If it doesn't, try re-including it. |
| Z-Wave commands are delayed or unreliable. | Weak Z-Wave signal; too many hops; interference. | Ensure the outlet is within 100 feet of the Z-Wave controller or another Z-Wave device. Optimize your Z-Wave network by adding more repeaters. |
Specifications
- Model Number: WO15Z-1
- Power: 120 VAC, 60 Hz
- Maximum Load: 15 Amps (Resistive), 600 Watts (Incandescent)
- Wireless Technology: Z-Wave
- Wireless Range: Up to 100 feet line of sight between the controller and/or the closest Z-Wave device
- Operating Temperature: 32-104°F (0-40°C)
- Dimensions: 1.63 x 1.75 x 4.13 inches
- Weight: 6.4 ounces
- Certifications: UL Listed
- Material: Plastic
- Color: White
Warranty and Support
Warranty
The GoControl WO15Z-1 Z-Wave Single Wall Outlet comes with a 1-year warranty against manufacturer defects from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, accident, unauthorized modification, or improper installation.
Technical Support
For technical assistance, troubleshooting, or warranty claims, please contact GoControl customer support. Refer to the GoControl official website for the most current contact information.
