ColorRite 2Tip Automotive Touch-up Paint Manual

Product Overview

The ColorRite 2Tip All-Inclusive Package provides a comprehensive solution for repairing small nicks and scratches on your vehicle's paint. This package is specifically formulated for the 2007 Dodge Charger with Linen Gold Pearl Metallic Clearcoat (color code CYG/PYG).

The 2Tip pen features two ends: one for the factory-matched color and the other for a high-quality clearcoat. The All-Inclusive Package also includes essential preparation and finishing materials for optimal results.

Image: The ColorRite 2Tip pen, showing the paint color and clearcoat ends, alongside a swatch of the Linen Gold Pearl Metallic color.

Package Contents

The All-Inclusive Package contains the following items:

• 2Tip Pen: Factory-matched color (CYG/PYG) and clearcoat.
• Primer Pen: For surface preparation.
• Prep Wipes (3): To remove wax or grease from the repair area.
• Latex Gloves: For protection during application.
• 3M Sandpaper Combo Pack: For surface smoothing.
• 3M Masking Tape: To protect surrounding areas.
• Tack Cloth: For dust removal.
• Polishing Compound: For final finishing.

Image: All components included in the ColorRite 2Tip All-Inclusive Package, laid out for inspection.

Setup and Preparation

1. Verify Color Code: Confirm your vehicle's paint code is CYG/PYG. This is crucial for an accurate color match.
2. Clean the Area: Thoroughly clean the damaged area and surrounding paint with soap and water. Use one of the provided Prep Wipes to remove any wax, grease, or contaminants. Allow to dry completely.
3. Sand (if necessary): For deeper scratches or rough edges, use the 3M sandpaper to gently smooth the area. Feather the edges of the scratch to ensure a smooth transition. Clean off any sanding dust with the tack cloth.
4. Mask Surrounding Area: Use 3M masking tape to protect the paint surrounding the repair area. This helps prevent accidental application and creates a clean edge.
5. Perform a Spray-Out Test: Before applying to your vehicle, perform a test application on an inconspicuous area or a test card. This allows you to verify the color match and practice your application technique.

Operating Instructions (Application)

Wear the provided latex gloves throughout the application process.

1. Apply Primer: If the scratch has exposed bare metal or plastic, apply a thin, even coat of primer using the primer pen. Allow the primer to dry completely according to its instructions (typically 10-15 minutes).
2. Apply Color: Shake the 2Tip color pen vigorously for at least 30 seconds. Use the chiseled nib to apply thin, even coats of the Linen Gold Pearl Metallic color directly into the scratch or chip.
   • For hairline scratches, use the thin edge of the nib.
   • For larger chips or scratches, use the wider edge.
   Allow each coat to dry for 10-15 minutes before applying the next. Build up the color in thin layers until it is level with the surrounding paint. Avoid applying too much paint at once, as this can lead to a raised repair.
3. Apply Clearcoat: Once the color coat is completely dry (allow at least 30 minutes to an hour after the final color coat), shake the clearcoat end of the 2Tip pen. Apply a thin, even layer of clearcoat over the repaired area. The clearcoat protects the color and provides a glossy finish. Apply 1-2 coats, allowing 10-15 minutes drying time between coats.
4. Final Drying: Allow the clearcoat to dry for at least 24 hours before proceeding with polishing. Full cure time may vary depending on temperature and humidity.

Maintenance and Finishing

1. Remove Masking Tape: Carefully remove the masking tape once the clearcoat has dried to the touch.
2. Polishing (Optional): After the clearcoat has fully cured (24-48 hours), you may use the provided polishing compound to blend the repaired area with the surrounding paint. Apply a small amount of compound to a soft, clean cloth and gently rub the repaired area in a circular motion. This helps to reduce any slight ridges and enhance the shine.
3. Protect the Repair: Avoid washing the repaired area with harsh chemicals or automated car washes for at least 30 days to allow the paint to fully harden.

Troubleshooting

• Messy Application / Dripping: The 2Tip pens can be prone to messiness if too much pressure is applied or if the pen is overfilled.
  • Solution: Apply light pressure. Work in a well-ventilated area and have a clean rag ready for immediate wipe-up. Masking the area thoroughly is essential.
• Slight Ridge After Repair: This can occur if too much paint is applied in one go, causing it to sit proud of the original surface.
  • Solution: Apply paint in very thin layers, allowing each to dry completely. After full cure, use the polishing compound to gently level the ridge. For more significant ridges, very fine wet sanding (P2000 grit or higher) followed by polishing may be required, but proceed with caution.
• Color Mismatch: While ColorRite guarantees a match to the original factory color, variations can occur due to vehicle age, sun exposure, or previous repairs.
  • Solution: Always perform a "spray-out" test on an inconspicuous area or test card first. If the match is unsatisfactory, contact ColorRite support.

Specifications

Warranty Information

ColorRite guarantees that their paint will match the ORIGINAL factory color (CYG/PYG) of your 2007 Dodge Charger. For specific warranty details regarding product defects or performance, please refer to the official ColorRite website or contact their customer support directly. Keep your purchase receipt for any warranty claims.

Support and Contact

For further assistance, technical support, or inquiries regarding your ColorRite product, please visit the official ColorRite website or contact their customer service department. A dedicated team of specialists is available to help you achieve the best possible results.

Website: www.colorrite.com (Note: This is a placeholder URL, please refer to the product packaging for the exact support website.)