Bosch 00611317 Reed Contact for Dishwasher - Instruction Manual

Introduction

This manual provides essential information for the installation, operation, maintenance, and troubleshooting of the Bosch 00611317 Reed Contact. This component is a crucial replacement part designed for various Bosch and Siemens dishwashers, responsible for accurately detecting water levels and ensuring proper water intake during wash cycles. Please read these instructions carefully before proceeding with installation or any related procedures.

Compatibility

The Bosch 00611317 Reed Contact is compatible with a wide range of Bosch, Siemens, and Koenic dishwasher models. Please verify your appliance's model number against the following list to ensure compatibility:

• Siemens Models: SC73M611, SC73M612, SC73M613, SC73M810, SC74M620, SC74M621, SC75M530, SC76M520, SC76M522, SC76M530, SC76M531, SC76M532, SC76M540, SC76M541, SC76M640, SC78M530, SK23E800, SK23E810, SK25E100, SK25E200, SK25E201, SK25E202, SK25E203, SK25E210, SK25E211, SK26E200, SK26E201, SK26E220, SK26E221, SK26E800, SK26E801, SK26E820, SK26E821, SK75M520, SK75M521, SK75M530, SK75M531, SK75M532, SK76M530, SK76M540, SK76M544, SK78M530, SN45N582, SN45N583, SN45N584, SN45N585, SN45N588, SN45N589, SN45P530, SN45P532, SN45P582, SN45T280, SN45T281, SN45T282, SN45T283, SN45T284, SN45T530, SN46E581, SN46L500, SN46L530, SN46L570, SN46L582, SN46M080, SN46M200, SN46M201, SN46M203, SN46M230, SN46M281, SN46M282, SN46M283, SN46M290, SN46M291, SN46M292, SN46M293, SN46M500, SN46M501, SN46M530, SN46M531, SN46M535
• Bosch Models: SBV85M43, SBV85M44, SBV86M50, SBV86M60, SBV87TD01E, SBV87TX01H, SBV88PX00N, SBV88PX16N, SBV88TD01E, SBV88TX01N, SBV88TX03H, SBV88TX06E, SBV88TX16E, SBV88TX26E, SBV88TX36E, SBV90E00, SBV90E30, SBV90M10, SBV93M00, SBV93M10, SBV93M30, SBV93M40, SBV93M50, SBV93M60, SBV95M00, SBV95M10, SBV95M20, SBV95T10, SBV96M00, SBV96M10, SBV98M00, SBV99M20, SBV99M30, SBV99T10, SCE42M06, SCE52M55, SCE52M65, SCE53M05, SCE53M25, SCE53M35, SCE63M05, SCE63M15, SCE63M25, SCE64M05, SCE64M06, SCE64M55, SCE64M65, SGE53U52, SGE53U55, SGE53U56, SGE63E05, SGE63E06, SGE63E15, SGE68U5, SGV63E03, SGV68U53, SGX68U55, SHE68E05, SHE68E15, SHE7ER55, SHE89PW75N, SHE8ER55, SHE9PT55, SHEM78WH5N, SHV58E13, SHV68E13, SHV7ER53, SHV89PW73N, SHV9ER53, SHV9PT53, SHX58E15, SHX58E25, SHX5ER55, SHX68E05, SHX68E15, SHX7ER55, SHX89PW75N, SHX8ER55, SHX9PT55, SHX9PT75, SHX9PT775NL
• Koenic Models: 1KDW64018I, 1KDW64018U, 1KDW64019I, 1KDW64019U

Setup and Installation

Replacing the reed contact requires careful attention. If you are unsure about any step, it is recommended to consult a qualified appliance technician.

1. Safety First: Before beginning any work, ensure the dishwasher is completely disconnected from the main power supply by unplugging it or switching off the circuit breaker. Also, turn off the water supply to the dishwasher.
2. Access the Dishwasher Interior:
   • Remove the top cover of the dishwasher. This usually involves unscrewing a few screws at the back.
   • Locate and remove the left side panel of the dishwasher. This typically involves unscrewing two screws at the front (behind the door seal) and one at the top rear. Carefully lift the metal plate slightly upwards, then pull it backward to unclip it. Allow the plate to drop downwards to access the interior.
3. Locate the Reed Contact (Flow Meter): The reed contact is often housed within a small plastic box, which is part of the flow meter assembly. This assembly is usually located on the left side of the dishwasher's interior, connected to the water intake system.
4. Replace the Component: Carefully open the plastic housing to expose the small electronic circuit board (the reed contact). Gently remove the old circuit board from its plastic holder and insert the new Bosch 00611317 reed contact in its place, ensuring it is correctly oriented and seated.
5. Reassemble: Reverse the disassembly steps. Reattach the side panel, ensuring all clips and screws are securely fastened. Replace the top cover.
6. Test Operation: Reconnect the dishwasher to the main power supply and turn on the water supply. Run a test cycle to ensure the dishwasher fills with water correctly and operates without error codes.

Operating

The Bosch 00611317 Reed Contact is an internal component that functions automatically as part of your dishwasher's control system. Once correctly installed, it requires no direct user operation. Its purpose is to monitor the water flow and level within the dishwasher, signaling the control unit to ensure the correct amount of water is used for each wash cycle. Normal dishwasher operation should resume once the part is installed and functioning correctly.

Maintenance

The reed contact itself is a sealed electronic component and does not require routine maintenance. Its longevity is generally tied to the overall cleanliness and proper functioning of the dishwasher's water system. To help prevent issues that might affect the reed contact or other water-sensing components:

• Regularly clean your dishwasher's filters to prevent debris buildup.
• Use appropriate dishwasher detergents and rinse aids to minimize limescale and residue accumulation.
• Periodically run a dishwasher cleaning cycle with a specialized cleaner.

Troubleshooting

If your dishwasher is experiencing issues related to water intake or level detection, the reed contact may be a contributing factor. Common symptoms and troubleshooting steps include:

• Symptom: Dishwasher not filling with water, or filling with insufficient water.
  Possible Cause: Faulty reed contact or flow meter assembly.
  Action: Ensure the new reed contact is correctly installed. Check for any blockages in the water inlet hose or the dishwasher's internal water pathways.
• Symptom: Dishwasher displaying error codes such as E30 or 30:00 (specific to some Bosch/Siemens models), indicating a water flow or water level issue.
  Possible Cause: Malfunctioning reed contact sending incorrect signals.
  Action: Verify the installation of the replacement part. If the error persists, other components of the water system or control board might be at fault.
• Symptom: Dishwasher overfilling or continuously draining.
  Possible Cause: Incorrect signals from the reed contact or other water level sensors.
  Action: Recheck the installation. Ensure no wires are pinched or connections are loose.

If troubleshooting steps do not resolve the issue, it is advisable to contact a certified appliance technician for further diagnosis and repair.

Specifications

Warranty and Support

Specific warranty details for the Bosch 00611317 Reed Contact should be obtained from your point of purchase or directly from Bosch. As a replacement part, its warranty may differ from that of a complete appliance.

For technical support, further assistance, or to locate authorized service centers, please refer to the official Bosch website or contact Bosch customer service in your region. Always provide your dishwasher's full model and serial number when seeking support.