RIGID Industries 46509 Fog Light Mount Kit for Toyota Tacoma Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation and maintenance of the RIGID Industries 46509 Fog Light Mount Kit. This kit is designed to allow the integration of RIGID Industries SRM-Series LED lights (sold separately) into the OEM fog lamp locations of 2012 and newer Toyota Tacoma vehicles. The mount kit ensures a clean, factory-like appearance without requiring modifications to the vehicle's bumper.

2. Safety Information

• Always disconnect the vehicle's battery before beginning any electrical work.
• Wear appropriate personal protective equipment, including safety glasses and gloves.
• Ensure the vehicle is parked on a level surface with the parking brake engaged.
• If you are unsure about any step of the installation process, consult a qualified automotive technician.
• Do not overtighten fasteners, as this may damage components.

3. Package Contents

Verify that all components are present before beginning installation:

• RIGID Industries 46509 Fog Light Mount Plates (2)
• All necessary installation hardware (bolts, nuts, washers)

Note: RIGID Industries SRM-Series LED lights are sold separately and are not included with this mount kit.

4. Product Features

• Material: High-quality stainless steel construction for durability.
• Finish: Black powder-coated for corrosion resistance and a sleek appearance.
• Installation: Designed for a direct fit into OEM fog lamp locations without drilling or cutting.
• Compatibility: Specifically engineered for 2012+ Toyota Tacoma models.
• Origin: Made in USA.

5. Setup and Installation

Follow these steps to install the RIGID Industries 46509 Fog Light Mount Kit:

1. Prepare Vehicle: Park the Toyota Tacoma on a level surface, engage the parking brake, and turn off the engine. Disconnect the negative terminal of the vehicle's battery.
2. Access Fog Light Area: Depending on your specific Tacoma model and trim, you may need to remove or partially loosen the front bumper or fender liner to access the OEM fog light housing. Refer to your vehicle's service manual for specific instructions on accessing this area.
3. Remove OEM Fog Lights: Carefully unclip or unbolt the factory fog lights from their housings. Disconnect any wiring harnesses.
4. Attach Mount Kit: Position one of the RIGID Industries mount plates into the OEM fog light location. The mount is designed to utilize existing mounting points. Secure it using the provided hardware. Do not fully tighten at this stage.
5. Install SRM-Series LED Light: Mount your RIGID Industries SRM-Series LED light (sold separately) onto the newly installed mount plate using the hardware provided with your SRM-Series light.
6. Adjust and Tighten: Once the SRM-Series light is secured to the mount plate, adjust its position for optimal beam alignment. Fully tighten all mounting hardware for both the mount plate and the LED light.
7. Repeat for Other Side: Follow steps 3-6 for the opposite side of the vehicle.
8. Wiring (if applicable): Connect the wiring harness for your SRM-Series LED lights according to the instructions provided with the lights. Ensure all connections are secure and properly insulated.
9. Reassemble Vehicle: Reinstall any bumper components or fender liners that were removed.
10. Reconnect Battery: Reconnect the negative terminal of the vehicle's battery.
11. Test Lights: Turn on your vehicle and test the functionality of the newly installed fog lights.

Image 1: Rigid Industries 46509 Fog Light Mount Kit installed in a Toyota Tacoma bumper. This image shows the Rigid Industries 46509 Fog Light Mount Kit installed in the OEM fog lamp location of a Toyota Tacoma. A Rigid Industries SRM-Series LED light is visible within the mount, demonstrating the integrated appearance. Note: Lights are sold separately.

6. Operating Instructions

This product is a mount kit and does not have operational functions independently. The operation of the fog lights will depend on the specific RIGID Industries SRM-Series LED lights installed and their associated wiring harness and switch. Refer to the instruction manual provided with your SRM-Series LED lights for detailed operating procedures.

7. Maintenance

The RIGID Industries 46509 Fog Light Mount Kit is constructed from durable stainless steel with a powder-coated finish, requiring minimal maintenance.

• Cleaning: Clean the mount plates periodically with mild soap and water to remove dirt and road grime. Avoid abrasive cleaners or harsh chemicals that could damage the powder coat finish.
• Inspection: Periodically inspect all mounting hardware to ensure it remains tight. Check for any signs of corrosion or damage to the mount plates.

8. Troubleshooting

• Mount Kit Does Not Fit: Double-check that your vehicle is a 2012 or newer Toyota Tacoma. Ensure you are attempting to install the mount in the correct OEM fog lamp location.
• Lights Not Functioning: This issue is typically related to the SRM-Series LED lights or their wiring. Refer to the troubleshooting section of your SRM-Series LED light manual. Verify all electrical connections are secure and the battery is properly reconnected.
• Vibration/Rattling: Ensure all mounting hardware for both the mount kit and the LED lights is fully tightened.

9. Specifications

10. Warranty and Support

The RIGID Industries 46509 Fog Light Mount Kit is backed by RIGID Industries' limited lifetime warranty. For specific details regarding warranty coverage, claims, or technical support, please contact RIGID Industries directly through their official website or customer service channels.