Introduction
The Liberty Garden 708 Steel Decorative Wall Mount Garden Hose Reel is designed for efficient and organized storage of up to 125 feet of 5/8-inch garden hose. Constructed from durable, weather-resistant powder-coated steel, it features a convenient top shelf for garden tools and nozzles. This manual provides detailed instructions for proper installation, operation, and maintenance to ensure long-lasting performance.
Safety Information
Always observe the following safety precautions during installation and use of this product:
- Wear appropriate personal protective equipment, including safety glasses and gloves, when handling tools and during installation.
- Ensure the mounting surface is structurally sound and capable of supporting the weight of the hose reel and a full hose.
- Do not drill into electrical wires, plumbing, or gas lines. Use a stud finder to locate studs or check for utilities before drilling.
- Keep children and pets away from the work area during installation.
- Do not overtighten fasteners, as this may damage the product or mounting surface.
- Ensure all connections are secure to prevent leaks.
Package Contents
Verify that all components are present before beginning installation:
- Liberty Garden 708 Steel Decorative Wall Mount Garden Hose Reel (fully assembled)
- 5-feet of leader hose
- Note: Mounting hardware is not included and must be purchased separately based on your mounting surface.
Tools Required
The following tools are recommended for installation:
- Hammer Drill (for masonry) or Power Drill (for wood)
- 7/16" and 3/8" Sockets and Socket Wrench
- Pliers
- Level
- Hammer
- Stud Finder (for wood)
- Gloves
- Eye and Hearing Protection
- Black Marker
- Masking Tape
- Appropriate drill bits (5/16" concrete drill bit for masonry anchors, 1/4" concrete drill bit for concrete screws, 1/4" wood drill bit for wood screws)
Installation
This section provides instructions for mounting your hose reel. The Liberty Garden 708 model has a width of 16 inches between mounting points. Ensure you select the correct mounting hardware for your specific wall type.
Installation Video Guide
This video demonstrates the installation process for Liberty Garden Wall Mount Hose Reels, including models 704, 705, 708, and 710. It covers both masonry and wood stud mounting methods.
Mounting on Masonry (Brick/Concrete)
For masonry walls, you will need (4) 5/16" x 2 1/2" masonry screws with anchor sleeves and (4) 5/16" washers, or (4) 5/16" x 2 1/2" concrete screws with (4) 5/16" washers. A 5/16" concrete drill bit (for anchors) or 1/4" concrete drill bit (for concrete screws) is also required.
- Position and Mark: Hold the hose reel against the brick wall at the desired height. Use a level to ensure it is straight. Mark the locations of the four suspension holes on the brick using a black marker. Do not drill into the mortar.
- Prepare Drill Bit: For masonry screws with anchor sleeves, compare the 5/16" concrete drill bit to the anchor sleeve and add masking tape to the drill bit to mark the desired pilot hole depth. For concrete screws, tape your depth on the 1/4" concrete drill bit.
- Drill Pilot Holes: Using a hammer drill, drill pilot holes at the marked locations.
- Insert Anchors (if applicable): If using anchor sleeves, slide each sleeve into its hole, tapping lightly with a hammer until the desired depth is reached.
- Secure Hose Reel: Align the hose reel's suspension holes over the anchors/pilot holes. Insert the masonry screws with washers (and lock washers/nuts if using anchor sleeves) and tighten securely with a 7/16" or 3/8" socket wrench.
Mounting on Wood Studs
For wood-studded walls, you will need (4) 5/16" x 2 1/2" wood screws and (4) 5/16" washers. A 1/4" wood drill bit is also required.
- Locate Studs: Use a stud finder to locate the wooden studs in your wall. The hose reel is designed to align with typical 16-inch wood stud spacing.
- Position and Mark: Hold the hose reel against the wall, ensuring the mounting holes align with the studs. Use a level to ensure it is straight. Mark the position of each suspension hole on the wall with a black marker.
- Drill Pilot Holes: Using a power drill, drill pilot holes 1/4" in diameter and 2 1/2" deep at the marked positions.
- Secure Hose Reel: Align the hose reel's suspension holes with the pilot holes. Attach the hose reel to the wall using the wood screws and washers, tightening securely with a socket wrench.
Attaching the Hose Reel to the Base (for Navigator models, if applicable)
If your model has a separate base and reel assembly (like the Navigator 710 shown in the video), follow these steps:
- Attach the hose reel to the base shelf by hanging the reel on the small slot located at the front of the base.
- Line up the holes in the hose reel with the base shelf and insert the long Allen bolts.
- Tighten the Allen bolts with the supplied Allen wrench. Pliers may be needed to hold and tighten the lock nuts.
Operating Instructions
Using your Liberty Garden 708 hose reel is straightforward:
- Connect Water Supply: Attach the included 5-foot leader hose to your outdoor water spigot and to the inlet connection on the hose reel. Ensure all connections are tight to prevent leaks.
- Attach Garden Hose: Connect your garden hose (not included) to the outlet connection on the hose reel.
- Unwinding the Hose: To unwind the hose, simply pull the hose away from the reel. The reel will rotate freely, allowing the hose to extend.
- Winding the Hose: To wind the hose back onto the reel, turn the crank handle clockwise. Guide the hose evenly across the reel to prevent tangling and ensure proper storage.
Maintenance
Proper maintenance will extend the life of your hose reel:
- Cleaning: Periodically clean the hose reel with a damp cloth to remove dirt and debris. Avoid abrasive cleaners that could damage the powder-coat finish.
- Lubrication: Apply a silicone-based lubricant to moving parts, such as the crank mechanism and any rotating joints, annually or as needed to ensure smooth operation.
- Winterization: Before freezing temperatures, disconnect the hose reel from the water supply and drain all water from the hose and reel. Store the hose reel indoors or cover it to protect it from harsh winter conditions.
- Inspect Connections: Regularly check all hose connections for wear, cracks, or leaks. Replace worn washers or fittings as necessary.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaks from connections | Loose connections, worn washers, damaged hose/fittings | Tighten all connections. Replace worn rubber washers. Inspect hoses and fittings for damage and replace if necessary. |
| Hose does not wind smoothly | Hose tangled, reel mechanism dry, excessive hose length | Ensure hose is not tangled before winding. Apply silicone lubricant to the reel mechanism. Ensure hose length does not exceed the reel's capacity. |
| Reel is wobbly after installation | Loose mounting hardware, unstable mounting surface | Check and tighten all mounting screws. Verify the mounting surface is solid and secure. |
For further troubleshooting or specific issues, please refer to the official Troubleshooting Guide (PDF) or contact Liberty Garden customer support.
Specifications
- Model: 708
- Brand: Liberty Garden
- Material: Steel
- Color: Bronze
- Hose Capacity: Holds 125-feet of 5/8-inch garden hose (hose not included)
- Item Dimensions (L x W x H): 15 x 21 x 15.7 inches
- Item Weight: 12 pounds
- Installation Method: Wall Mount
- Operation Mode: Manual
- Included Components: Hose Reel, 5-feet leader hose
Warranty and Support
For warranty information, please refer to the documentation included with your product packaging or visit the official Liberty Garden website. For customer support, contact the manufacturer directly.