LG AEQ73110205 Ice Maker Assembly Kit Instruction Manual

1. Introduction

This manual provides essential instructions for the installation, operation, maintenance, and troubleshooting of your LG AEQ73110205 Ice Maker Assembly Kit. This kit is an authorized Original Equipment Manufacturer (OEM) replacement part designed for various LG brand refrigerator models. Please read this manual thoroughly before attempting any installation or operation to ensure proper function and safety.

2. Safety Information

Always prioritize safety when working with electrical appliances. Failure to follow these safety guidelines may result in property damage, personal injury, or death.

• Disconnect Power: Always unplug the refrigerator from the power outlet before attempting any installation, maintenance, or repair.
• Professional Installation: If you are unsure about any step, it is recommended to seek assistance from a qualified appliance technician.
• Handle with Care: The ice maker assembly contains delicate components. Handle it carefully to avoid damage.
• Water Supply: Ensure the refrigerator's water supply is turned off before beginning installation.

3. Package Contents

Verify that all components are present before beginning installation:

• LG AEQ73110205 Ice Maker Assembly Kit
• Associated appliance replacement parts (as included by manufacturer)

4. Installation Instructions

This section outlines the general steps for replacing your LG ice maker. Specific refrigerator models may vary slightly. Refer to your refrigerator's service manual for detailed model-specific instructions if available.

1. Preparation:
   • Unplug the refrigerator from the electrical outlet.
   • Remove the existing ice bin from the freezer compartment.
2. Remove Old Ice Maker:
   • Locate and remove the four screws with metal-colored tops that secure the ice maker assembly. Typically, there are two at the bottom (left and right), one in the middle, and one at the top. Do not remove any screws that are painted white, as these typically secure the ice maker to its plastic back plate.
   • Carefully pull the old ice maker assembly, along with its attached plastic back plate, out of the refrigerator compartment.
   • Disconnect the main electrical connector from the old ice maker assembly.
3. Separate Components (if necessary):
   • If your new ice maker assembly is not pre-attached to a back plate, or if you need to reuse the existing back plate, you may need to separate the old ice maker from its back plate. This usually involves removing four additional screws with white paint on top and disconnecting any secondary electrical connectors.
4. Install New Ice Maker:
   • If separated, attach the new ice maker to the plastic back plate using the appropriate screws.
   • Connect all necessary electrical connectors to the new ice maker. Ensure that all wires and wire bundles are carefully routed within their designated cutouts, recesses, and races. Improper routing can cause damage to wires or place excessive stress on plastic components, particularly near the optical sensor.
   • Position the assembled new ice maker and back plate into the refrigerator compartment.
   • Re-insert the four metal-top screws and tighten them securely, but do not overtighten.
5. Final Steps:
   • Plug the refrigerator back into the electrical outlet.
   • Locate the ice maker's ON/OFF switch (refer to the image below) and ensure it is in the "ON" position.
   • Allow several hours (typically 12-24 hours) for the ice maker to fill with water and begin producing ice. The first few batches of ice may be smaller or have an unusual taste; discard them.

Image 1: LG AEQ73110205 Ice Maker Assembly Kit. This image displays the complete ice maker unit, including the main housing, wiring harness, and the ice tray. The ON/OFF switch is visible on the front, and an instructional label indicates that both non-tilted and tilted ice tray positions are normal during operation.

5. Operating the Ice Maker

Once installed and powered, the ice maker operates automatically to produce ice. Ensure the ON/OFF switch is in the "ON" position for operation.

• Ice Production Cycle: The ice maker will automatically fill with water, freeze it into cubes, and then eject the cubes into the ice bin. This cycle repeats as long as the ice maker is on and the water supply is active.
• Ice Level Sensor: The ice maker is equipped with a sensor that detects the ice level in the bin. When the bin is full, the ice maker will temporarily stop production until more ice is used.
• Tray Positions: As indicated on the unit, both the non-tilted and tilted positions of the ice tray are normal during operation. The tray tilts to eject ice.
• Turning Off: To stop ice production, move the ON/OFF switch to the "OFF" position.

6. Maintenance

Regular maintenance helps ensure optimal performance and longevity of your ice maker.

• Cleaning: Periodically remove the ice bin and clean it with mild soap and warm water. Rinse thoroughly and dry completely before returning it to the freezer.
• Ice Tray Condition: Over time, the plastic surface of the ice tray may become porous, causing ice cubes to stick. If this occurs, cleaning the tray thoroughly may help. If the issue persists, replacement of the ice maker may be necessary.
• Water Filter: Ensure your refrigerator's water filter is replaced regularly according to the manufacturer's recommendations to maintain water quality and prevent mineral buildup in the ice maker.

7. Troubleshooting

If your ice maker is not functioning correctly, review the following common issues and solutions:

8. Specifications

9. Warranty and Support

This LG AEQ73110205 Ice Maker Assembly Kit is an authorized OEM part. For specific warranty information, please refer to the documentation provided with your original refrigerator purchase or contact LG customer support directly. Keep your purchase receipt as proof of purchase for any warranty claims.

For technical assistance or further inquiries, please contact LG customer service through their official website or support channels.