Godspeed AK-055-A Adjustable Rear Camber Kit Instruction Manual

1. Safety Information

WARNING: This product is strictly for off-road and show use only. It is not designed for use with excessive camber or air suspensions. This product is not intended to achieve an "extreme stance look." Any form of driving with an "extreme stance look" is dangerous and irresponsible. Professional installation is highly recommended.

2. Product Overview

The Godspeed AK-055-A Adjustable Rear Camber Kit is designed for Honda Accord (CG/CF) models from 1998 to 2002, including all trims. This kit provides adjustable rear camber correction, which is beneficial for lowered vehicles to improve handling characteristics and extend tire life. The camber arms are constructed from heavy-duty steel alloy with a corrosion-resistant finish, ensuring durability and reliability for both daily driving and high-performance applications.

Figure 2.1: Godspeed AK-055-A Adjustable Rear Camber Kit components.

3. Specifications

4. Installation Instructions (Setup)

Installation of the Godspeed AK-055-A Rear Camber Kit requires specialized tools and automotive knowledge. It is strongly recommended that installation be performed by experienced professionals to ensure proper fitment, safety, and vehicle alignment. No installation instructions are included with the product.

General Installation Steps (Professional Guidance Recommended):

1. Safely lift and support the vehicle on jack stands or a lift. Remove the rear wheels.
2. Locate the factory rear camber arms. These are typically part of the rear suspension assembly.
3. Carefully remove the bolts securing the factory camber arms to the chassis and the knuckle. Retain all hardware unless new hardware is provided.
4. Install the new Godspeed AK-055-A Adjustable Rear Camber Arms in place of the removed factory arms. Ensure proper orientation and secure all mounting points. Do not fully tighten bolts until the vehicle is at ride height.
5. Once the new arms are installed, re-install the wheels and lower the vehicle.
6. Perform an initial visual alignment check.
7. Crucially, a professional wheel alignment must be performed immediately after installation to set the correct camber, toe, and thrust angles. Failure to do so can result in unsafe driving conditions and premature tire wear.

Figure 4.1: Illustrative diagram of the rear suspension, highlighting the camber arm location (AK-055).

5. Adjustment (Operating)

The Godspeed AK-055-A Rear Camber Kit allows for camber adjustment of approximately +/- 3 degrees. This adjustment is typically made by rotating the central body of the camber arm, which lengthens or shortens the arm, thereby changing the wheel's camber angle.

Adjustment Procedure:

1. Loosen the lock nuts on the adjustable section of the camber arm.
2. Rotate the central body of the arm to achieve the desired camber setting. Lengthening the arm typically increases positive camber, while shortening it increases negative camber.
3. Once the desired setting is achieved, tighten the lock nuts securely.
4. After any adjustment, a professional wheel alignment is mandatory to ensure proper vehicle dynamics and tire wear.

Figure 5.1: Illustration of camber arm adjustment mechanisms and recommended maximum range.

6. Maintenance

Regular inspection and maintenance are crucial for the longevity and performance of your adjustable rear camber kit.

• Periodic Inspection: Visually inspect the camber arms, bushings, and ball joints for any signs of wear, damage, or corrosion at least every 6 months or during routine vehicle servicing.
• Tightness Check: Ensure all bolts and nuts, especially the adjustment lock nuts, remain securely tightened. Re-torque to manufacturer specifications if available, or consult a professional.
• Cleaning: Keep the components clean from dirt, salt, and road debris, which can accelerate wear and corrosion.
• Lubrication: If the ball joints or bushings are of a serviceable type (with grease fittings), lubricate them according to standard automotive practices.
• Alignment Check: If you notice any changes in vehicle handling or unusual tire wear, have a professional alignment check performed promptly.

7. Troubleshooting

Should you encounter issues after installing the Godspeed AK-055-A Rear Camber Kit, consider the following common problems and solutions:

• Uneven Tire Wear: This is often a primary indicator of incorrect alignment. Immediately seek professional wheel alignment services.
• Unusual Noises (e.g., clunking, squeaking): Check all mounting bolts for proper torque. Inspect bushings and ball joints for wear or damage. Loose components or worn parts can cause noise.
• Difficulty Adjusting Camber: Ensure lock nuts are fully loosened. If components are seized, they may require lubrication or replacement.
• Poor Vehicle Handling: This can be caused by incorrect alignment settings or improperly installed components. Re-verify installation and obtain a professional alignment.

For persistent issues, consult with a qualified automotive technician or contact Godspeed customer support.

8. Warranty and Support

Specific warranty terms for the Godspeed AK-055-A Adjustable Rear Camber Kit are typically provided with the product packaging or can be found on the official Godspeed website. Please retain your proof of purchase for any warranty claims.

For technical support, installation inquiries, or warranty service, please contact Godspeed directly through their official website or the retailer from whom the product was purchased.