Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Watco 590-PP-PVC-CP Innovator Push Pull Chrome PVC Bath Waste Assembly. This assembly is designed for use with most bathtubs up to 16 inches deep, providing a complete solution for your bath waste system.
Figure 1: Watco 590-PP-PVC-CP Innovator Push Pull Chrome PVC Bath Waste Assembly. This image displays the complete bath waste assembly, including the overflow plate, the PVC piping, and the push-pull drain stopper mechanism.
Safety Information
- Always turn off the water supply before beginning any plumbing work.
- Wear appropriate personal protective equipment, such as safety glasses and gloves.
- Ensure all connections are properly sealed to prevent leaks.
- If you are unsure about any step, consult a qualified plumber.
- Keep small parts away from children.
Setup and Installation
Tools Required:
- Plumber's putty or silicone sealant
- Screwdriver (Phillips or flathead, depending on overflow plate screws)
- Adjustable wrench or channel locks
- Rag or cloth
Installation Steps:
- Prepare the Bathtub: Ensure the overflow and drain openings in the bathtub are clean and free of debris.
- Install the Overflow Assembly:
- Apply plumber's putty or silicone sealant around the back of the overflow flange.
- Insert the overflow pipe through the overflow opening from the front of the tub.
- From behind the tub, connect the overflow pipe to the overflow tee fitting. Secure with the provided gasket and nut, ensuring a watertight seal.
- Attach the chrome overflow plate to the overflow pipe using the provided screws.
- Install the Drain Shoe Assembly:
- Apply plumber's putty or silicone sealant to the underside of the drain flange (the part that sits inside the tub).
- Insert the drain flange into the drain opening from inside the tub.
- From underneath the tub, attach the drain shoe (the lower horizontal pipe) to the drain flange. Ensure the rubber gasket is correctly seated between the tub and the shoe. Tighten the nut securely with an adjustable wrench, but do not overtighten.
- Connect the Waste Assembly: Connect the overflow tee to the drain shoe using the provided PVC pipe and fittings. Ensure all connections are tight and properly sealed.
- Install the Push-Pull Stopper: Insert the push-pull stopper mechanism into the drain opening. It typically threads into the drain shoe or is secured with a set screw.
- Test for Leaks: Fill the bathtub with water and allow it to drain. Carefully inspect all connections for any signs of leakage. Tighten connections as necessary.
Operating Instructions
The Watco Innovator Push Pull Bath Waste Assembly features a simple push-pull mechanism for opening and closing the drain.
- To Close the Drain: Firmly push down on the drain stopper knob. The stopper will engage, sealing the drain and allowing the tub to fill with water.
- To Open the Drain: Firmly pull up on the drain stopper knob. The stopper will disengage, allowing water to drain from the tub.
Maintenance
Regular maintenance will ensure the longevity and proper function of your bath waste assembly.
- Cleaning the Stopper: Periodically remove the push-pull stopper (it usually unthreads or pulls out) and clean any hair or debris that may have accumulated around it. Use a mild soap and water solution.
- Cleaning the Overflow Plate: Wipe the chrome overflow plate with a soft cloth and a non-abrasive cleaner to maintain its finish.
- Drain Cleaning: If the drain becomes slow, use a non-corrosive drain cleaner or a plumbing snake designed for residential use. Avoid harsh chemicals that could damage PVC pipes or chrome finishes.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Leakage around drain or overflow | Improperly sealed connections or loose nuts. | Tighten all nuts. If leaks persist, disassemble, reapply plumber's putty or sealant, and reassemble. |
| Drain stopper not holding water | Debris under the stopper or stopper mechanism malfunction. | Remove and clean the stopper. Inspect the stopper's rubber seal for damage. Replace if necessary. |
| Slow draining | Hair or debris buildup in the drain pipe. | Remove the stopper and clear any visible obstructions. Use a drain snake or a non-corrosive drain cleaner. |
Specifications
| Brand | Watco |
| Model Number | 590-PP-PVC-CP |
| Material | Chrome (trim), PVC (pipes) |
| Item Weight | 2 pounds |
| UPC | 640263021703 |
| Tub Depth Compatibility | Up to 16 inches |
Warranty and Support
For specific warranty information and customer support, please refer to the official Watco website or contact Watco customer service directly. Keep your purchase receipt as proof of purchase.
Manufacturer Contact: Please visit the Watco Manufacturing website for the most current contact information and support resources.