Inspired LED Cut and Connect Series Flex LED Kit User Manual

1. Introduction

The Inspired LED Cut and Connect Series Flex LED Kit provides an easy and affordable solution for custom LED lighting projects. This kit features solderless Tiger Paw LED Connectors, allowing users to create custom length LED strips for various applications. It is designed for straightforward installation, making it suitable for both beginners and experienced professionals.

This manual provides comprehensive instructions for the safe installation, operation, and maintenance of your Inspired LED Flex LED Kit.

2. Important Safety Information

• Read all instructions before installation and use.
• Do not connect the LED strips directly to AC power. Use only the provided 12V DC power supply.
• Ensure power is disconnected before performing any installation, maintenance, or troubleshooting.
• This product is designed for indoor use only. Do not expose to moisture or wet conditions.
• Do not bend the LED strips sharply or apply excessive force, as this may damage the internal circuitry.
• Keep out of reach of children.
• Do not cover the power supply or LED strips with flammable materials. Ensure adequate ventilation.
• If any part of the kit is damaged, discontinue use immediately and contact Inspired LED support.

3. Package Contents

Verify that all components listed below are included in your kit:

• 1 x 9.5ft (3M) Reel of Super Bright LED Flexible Strip Tape (Warm White, with 3M adhesive backing)
• 1 x 2 Amp Power Supply
• 1 x On/Off Switch
• 2 x Tiger Paw LED Connector Pairs
• 2 x 3 Foot Interconnect Cables
• 6 x Clips and Screws

Figure 3.1: Overview of all included components in the kit.

4. Setup and Installation

Follow these steps to install your Inspired LED Flex LED Kit. Ensure power is off before beginning.

4.1. Planning Your Installation

• Determine the desired locations for your LED lighting (e.g., under cabinets, shelves, display cases).
• Measure the lengths required for each section. The LED strip can be cut at designated points, typically every 0.625 inches (1.59 cm), marked by a copper pad.
• Plan the routing of interconnect cables and the placement of the power supply and on/off switch.

4.2. Cutting and Connecting LED Strips

1. Carefully cut the LED strip at the designated copper pads using sharp scissors.
2. To connect two LED strip sections or an LED strip to an interconnect cable, use the Tiger Paw LED Connectors. Open the connector by lifting the clear plastic tab.
3. Slide the end of the LED strip (or cable) into the connector, ensuring the copper pads on the strip align with the metal contacts inside the connector.
4. Press down the clear plastic tab firmly until it clicks into place, securing the connection.

Figure 4.1: Example of LED strip installation for under-cabinet and above-cabinet lighting.

4.3. Mounting the LED Strips

1. Clean the mounting surface thoroughly. Ensure it is dry and free of dust, grease, or debris. For best adhesion, wipe the surface with rubbing alcohol and let it dry.
2. Peel off the protective backing from the 3M adhesive on the back of the LED strip.
3. Carefully press the LED strip onto the desired surface, applying firm, even pressure along its entire length.
4. For added security, especially on vertical or frequently touched surfaces, use the provided clips and screws to secure the LED strip.

4.4. Connecting Power

1. Connect the on/off switch to the LED strip system. The switch has a male and female DC barrel connector.
2. Connect the 2 Amp Power Supply to the on/off switch.
3. Plug the power supply into a standard electrical outlet.

Figure 4.2: Under-cabinet lighting providing ambient illumination in a kitchen.

5. Operating Instructions

Once installed and connected to power, operating your Inspired LED lighting system is simple:

• Turning On/Off: Use the integrated on/off switch to control the lighting.
• Dimmable Feature: This kit is dimmable. If you wish to utilize dimming functionality, you will need to integrate a compatible 12V DC dimmer (sold separately) between the power supply and the LED strips. Refer to the dimmer's instructions for proper installation.

Figure 5.1: Example of LED lighting used to illuminate a bar area.

6. Maintenance

The Inspired LED Flex LED Kit requires minimal maintenance to ensure long-lasting performance.

• Cleaning: Ensure the power is off before cleaning. Gently wipe the LED strips and connectors with a soft, dry cloth. Do not use abrasive cleaners or harsh chemicals. Avoid getting water directly on the LED strips or electrical components.
• Adhesion: If the adhesive backing begins to lose its grip over time, you can reinforce the strips using the provided clips and screws, or by applying additional double-sided adhesive tape suitable for LED strips.
• Connection Check: Periodically check all connections (Tiger Paw connectors, interconnect cables, power supply) to ensure they are secure.

7. Troubleshooting

If you encounter issues with your Inspired LED Flex LED Kit, refer to the table below for common problems and solutions.

If the problem persists after trying these solutions, please contact Inspired LED customer support for further assistance.

8. Product Specifications

9. Warranty and Support

For warranty information and customer support, please contact Inspired LED directly. Details regarding specific warranty periods and terms are typically provided with your purchase documentation or can be found on the official Inspired LED website.

Contact Information:

• Visit the Inspired LED Store on Amazon for product information and accessories.
• Refer to the packaging or the manufacturer's website for direct contact details.