Product Overview
This manual provides instructions for the CUB CADET OEM Part Number 751-3141-14 Drain Hose. This hose is designed for efficient fluid drainage from compatible Cub Cadet equipment, replacing prior MPN GW-1909371, GW-1769006, and 751-3141-13. It ensures a clean and controlled process for maintenance tasks such as oil changes.
Figure 1: The Cub Cadet 751-3141-14 Drain Hose, a clear flexible tube with a fitting at one end.
Compatibility
The 751-3141-14 Drain Hose is compatible with a wide range of Cub Cadet models. Always refer to your original equipment owner's manual to verify compatibility for your specific model.
Partial List of Compatible Models:
- 1170, 1180, 1212, 1300, 1405, 1515, 1517, 1525, 1527, 1529, 1600, 1800
- 2130, 2135, 2150, 2155, 2160, 2164, 2165, 2166, 2176, 2185, 2186, 2206
- 3165, 3184, 3185, 3186, 3204, 3206, 3225, 3235, 3240
- GT-1054, GT-1222, GT-1554, GT-2186-44, GT-2186-48, GT-2521-48, GT-2523-54, GT-2542, GT-2544, GT-2550, GT-2554, GT-3100, GT-3200, GT-3204, GT-3235
- LGT-1050, LGT-1054, LGTX-1050, LGTX-1054
- LT-1018, LT-1022, LT-1024, LT-1040, LT-1042, LT-1045, LT-1046, LT-1050, LT-2042, LT-2138, LT-2180
- LTX-1040, LTX-1042, LTX-1045, LTX-1046, LTX-1046M, LTX-1050
- RZT-17, RZT-22, RZT-42, RZT-50, RZT-54, RZT-L34, RZT-L42, RZT-L46, RZT-L46 Fab, RZT-L50, RZT-L54, RZT-LX46 Fab, RZT-LX50 Fab, RZT-LX54 Fab, RZT-S50, RZT-S54, RZT-SX54 Fab
- SLT-1550, SLT-1554, SLTX-1050, SLTX-1054
- XT1-GT50, XT1-GT54 Fab, XT1-LT42, XT1-LT42 EFI, XT1-LT42B, XT1-LT42C, XT1-LT46, XT1-LT46 EFI Fab, XT1-LT46 Fab, XT1-LT50, XT1-LT50 Fab, XT1-ST54 Fab
- XT2-GX50 Fab, XT2-GX54 Fab, XT2-GX54D Fab, XT2-LX42, XT2-LX42 EFI, XT2-LX42 Fab, XT2-LX46, XT2-LX46 EFI Fab, XT2-LX46 Fab, XT2-LX46 LE Fab, XT2-LX50, XT2-LX54 Fab, XT2-SLX50, XT2-SLX50 EFI, XT2-SLX50 EFI Fab, XT2-SLX50 Fab, XT2-SLX54 Fab
- Z42, Z48, Z48L, Z54, Z54L, Z-Force 15, Z-Force S46, Z-Force S48, Z-Force S48 LP, Z-Force S54, Z-Force S60, Z-Force S60 LP, ZTT42 i1042, ZTT46 i1046, ZTT50 i1050
Setup and Installation
The Cub Cadet Drain Hose is designed for easy attachment to the oil drain spout of compatible equipment. Follow these steps for proper setup:
- Prepare the Area: Ensure the equipment is on a level surface. Place a suitable drain pan directly beneath the oil drain spout to collect the fluid.
- Locate Drain Spout: Identify the oil drain spout on your Cub Cadet equipment. Refer to your equipment's owner's manual for the exact location.
- Attach Hose: Carefully thread the end of the drain hose with the fitting onto the oil drain spout. Hand-tighten until snug. Do not overtighten, as this may damage the threads.
- Position Hose: Direct the open end of the hose into the drain pan, ensuring it is securely positioned to prevent spills.
Figure 2: A close-up view of the drain hose, showing the threaded end designed for attachment to equipment.
Operating Instructions
Once the drain hose is securely attached and positioned, proceed with the fluid drainage process as per your equipment's maintenance guidelines.
- Initiate Drainage: Open the drain valve or remove the drain plug on your equipment, allowing the fluid to flow through the hose into the collection pan.
- Monitor Flow: Observe the fluid flow through the clear hose to ensure it is draining properly and to prevent overflow of the collection pan.
- Complete Drainage: Allow all fluid to drain completely.
- Close Drain: Once drainage is complete, close the drain valve or reinsert the drain plug according to your equipment's manual.
- Remove Hose: Carefully unthread the drain hose from the spout. Be prepared for any residual drips.
Figure 3: The drain hose positioned for fluid collection, illustrating its flexibility and clear material for monitoring.
Maintenance and Storage
Proper maintenance and storage will extend the life of your drain hose.
- Cleaning: After each use, rinse the hose thoroughly with an appropriate cleaning solution to remove any residual fluids. Ensure it is completely dry before storage.
- Inspection: Regularly inspect the hose for any signs of wear, cracks, or damage. Check the integrity of the threaded fitting.
- Storage: Store the hose in a clean, dry place away from direct sunlight and extreme temperatures. Avoid kinking or bending the hose sharply during storage.
Figure 4: The drain hose coiled for compact storage, demonstrating its flexible nature.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fluid not draining or slow drainage. | Hose kinked or blocked. | Check for kinks in the hose. Clear any obstructions. Ensure the drain pan is not full. |
| Leaking at connection point. | Hose not tightened sufficiently or damaged fitting. | Ensure the hose is hand-tightened securely. Inspect the fitting for cracks or damage; replace if necessary. |
| Hose appears discolored or brittle. | Exposure to harsh chemicals or prolonged sunlight. | Replace the hose. Store in a cool, dry place away from direct sunlight. |
Specifications
- Part Number: 751-3141-14
- Replaces: 751-3141-13, GW-1909371, GW-1769006
- Product Dimensions: 9.5 x 5.5 x 1 inches
- Item Weight: 2.4 ounces
- Manufacturer: CUB CADET
- Material: Flexible, clear tubing
Warranty and Support
This Cub Cadet OEM part is covered by the manufacturer's standard warranty. For specific warranty details, claims, or technical support, please refer to the official Cub Cadet website or contact their customer service directly. Always use genuine Cub Cadet replacement parts to ensure compatibility and performance.
For more information, visit the official CUB CADET Store on Amazon or their corporate website.