Introduction
The SecoRüt 90125 is an advanced ultrasonic marten repellent module designed to protect vehicles from marten damage. This device emits high-frequency ultrasonic sounds and features an optical LED deterrent to keep martens away from your engine bay and other vulnerable areas. It operates on a 12V power supply, making it suitable for most vehicle electrical systems.
Key Features:
- Very high and strong acoustic pressure for effective deterrence.
- Equipped with a waterproof membrane for durability.
- Provides both optical (LED) and acoustic (loudspeaker) protection.
- Offers a wide range of coverage.
Figure 1: Angled view of the SecoRüt 90125 Ultrasonic Marten Repellent Module, showing the LED and branding.
Setup and Installation
Proper installation is crucial for the effective operation of the SecoRüt 90125 module. Please follow these steps carefully.
Safety Precautions:
- Always disconnect the vehicle's battery before beginning installation to prevent electrical shorts or damage.
- Ensure the module is installed in a location where it will not interfere with moving engine parts or heat sources.
- Wear appropriate safety gear, such as gloves and eye protection.
Installation Steps:
- Choose a Mounting Location: Select a suitable location within the engine compartment that is protected from direct water spray and excessive heat. The location should allow the ultrasonic sound and LED light to spread effectively throughout the engine bay. Avoid areas directly behind large components that could block the signal.
- Mount the Module: Use the integrated mounting tab to securely fasten the module. Screws or cable ties (not included) can be used. Ensure the module is stable and will not vibrate loose.
- Connect Power: The module requires a 12V power supply. Connect the red wire to a positive (+) 12V source. This can be directly to the battery's positive terminal (for continuous operation) or to an ignition-switched 12V source (for operation only when the vehicle is off). Connect the black wire to a negative (-) ground point on the vehicle chassis or battery. Ensure all connections are secure and insulated.
- Test Operation: Reconnect the vehicle's battery. The module should emit a high-frequency sound (which may be inaudible to humans) and the LED should flash, indicating proper function.
Figure 2: Top view of the module, showing the power wires and the LED indicator.
Operating Instructions
Once correctly installed and powered, the SecoRüt 90125 module operates automatically.
- Automatic Activation: The device will activate automatically when it receives 12V power. If connected directly to the battery, it will operate continuously. If connected to an ignition-switched source, it will operate when the ignition is off.
- Ultrasonic Emission: The module emits high-frequency ultrasonic sounds that are unpleasant for martens but generally inaudible to humans. These sounds create an uncomfortable environment, deterring martens from entering the protected area.
- LED Flashing: The integrated LED light will flash periodically, providing an additional visual deterrent to scare away martens, especially in low-light conditions.
- Continuous Protection: The combination of ultrasonic sound and flashing LED provides continuous, multi-sensory protection against marten damage.
Figure 3: Bottom view of the module, showing the ultrasonic speaker and 'MADE IN GERMANY' inscription.
Maintenance
The SecoRüt 90125 module is designed for low maintenance. However, periodic checks can ensure its continued effectiveness.
- Regular Cleaning: Occasionally, gently wipe the module's surface with a dry or slightly damp cloth to remove dust, dirt, or debris that might accumulate. Ensure the speaker grille and LED are clear.
- Check Connections: Periodically inspect the power connections (red and black wires) to ensure they remain secure and free from corrosion.
- Verify Operation: Confirm that the LED is flashing and the module is emitting sound (if audible to you, or by using a suitable ultrasonic detector) to ensure it is functioning correctly.
- Clear Obstructions: Ensure that no new components or debris in the engine bay are blocking the path of the ultrasonic waves or the LED light.
Troubleshooting
If your SecoRüt 90125 module is not functioning as expected, consider the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Module not activating (no LED flash, no sound) | No power supply; loose or incorrect wiring; blown fuse in vehicle circuit. | Check power connections (red wire to 12V, black wire to ground). Ensure battery is connected. Inspect vehicle's fuse box for any blown fuses related to the power source. |
| Marten activity continues despite module operation | Incorrect placement; ultrasonic waves blocked; martens have become accustomed to the sound (rare). | Relocate the module to a more open area in the engine bay, ensuring the speaker and LED have an unobstructed path. Remove any large objects blocking the signal. Consider adding additional deterrents if the problem persists. |
| LED flashes, but no audible sound (if applicable) | Speaker malfunction; sound is above human hearing range. | The ultrasonic sound is often inaudible to humans. If the LED is flashing, the module is likely operating. If you suspect a speaker issue, consult manufacturer support. |
Specifications
- Brand:
- SecoRüt
- Model Number:
- 90125
- Power Supply:
- 12V DC
- Deterrent Method:
- Ultrasonic sound, Flashing LED light
- Features:
- Waterproof membrane, High acoustic pressure, Wide range
- Manufacturer:
- SecoRüt
- ASIN:
- B00BSTYR74
- Date Listed on Amazon.com.be:
- May 31, 2022
Warranty and Support
Specific warranty information for the SecoRüt 90125 Ultrasonic Marten Repellent Module is not available in the provided product data. For detailed warranty terms, technical support, or service inquiries, please refer to the product packaging, the manufacturer's official website, or contact your retailer directly.
It is recommended to retain your proof of purchase for any warranty claims.