Philips LRA172000M OccuSwitch Wireless Wall Switch User Manual

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Philips LRA172000M OccuSwitch Wireless Wall Switch. Please read this manual thoroughly before installation and retain it for future reference.

2. Safety Information

WARNING: Risk of electric shock. Improper installation can lead to serious injury or death. Always turn off power at the circuit breaker before installation or servicing.

• This device is designed for use only with copper or copper clad wire.
• A connection to the Neutral wire is required for proper operation. Refer to the wiring scheme in the installation manual provided with the product.
• For indoor commercial use only.
• Ensure the device is used only with a compatible wireless sensor.
• Do not install if you are unfamiliar with electrical wiring. Consult a qualified electrician.

3. Package Contents

Verify that all components are present before beginning installation:

• Philips LRA172000M OccuSwitch Wireless Wall Switch (White)
• Installation Manual (enclosed)

Note: A wall plate is not included with this product and must be purchased separately.

Figure 1: Philips LRA1720 OccuSwitch Wireless Wall Switch product packaging.

4. Setup and Installation

Installation should only be performed by a qualified electrician or a person with a thorough understanding of electrical wiring.

4.1 Wiring Instructions

1. Turn off power: Locate the circuit breaker controlling the switch location and turn off the power. Verify power is off using a voltage tester.
2. Prepare wires: This device requires connection to a Neutral wire. Ensure you have access to Line (Hot), Load, Neutral, and Ground wires in the electrical box.
3. Connect wires: Follow the wiring diagram provided in the enclosed installation manual. Typically, connections are as follows:
   • Connect the Line (Hot) wire to the designated terminal on the switch.
   • Connect the Load wire to the designated terminal on the switch.
   • Connect the Neutral wire to the designated terminal on the switch.
   • Connect the Ground wire to the green ground screw in the electrical box.
4. Secure switch: Carefully fold the wires and insert the switch into the electrical box. Secure it with the provided screws.
5. Install wall plate: Attach a compatible wall plate (not included) over the switch.
6. Restore power: Turn the power back on at the circuit breaker.

Figure 2: Front view of the Philips OccuSwitch Wireless Wall Switch, showing wiring connections and a warning label.

Figure 3: Back view of the Philips OccuSwitch Wireless Wall Switch, displaying product labels including model number, FCC ID, and certifications.

5. Operating Instructions

The Philips LRA172000M OccuSwitch Wireless Wall Switch operates in conjunction with a compatible wireless sensor (not included). Once properly installed and paired with a sensor, the switch provides manual control over connected lighting or other loads.

Figure 4: The Philips OccuSwitch Wireless Wall Switch, shown installed in a standard wall plate.

• Manual ON/OFF: Press the top part of the rocker switch to turn the connected load ON. Press the bottom part of the rocker switch to turn the connected load OFF.
• Wireless Control: When paired with a compatible wireless occupancy sensor, the switch will respond to the sensor's signals, automatically turning lights on or off based on occupancy detection. Manual override is typically available via the rocker switch.

6. Maintenance

The Philips LRA172000M OccuSwitch Wireless Wall Switch requires minimal maintenance.

• Cleaning: To clean the switch, wipe it with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
• Inspection: Periodically inspect the switch for any signs of damage or loose connections. If any issues are found, turn off power and consult a qualified electrician.

7. Troubleshooting

If you experience issues with your Philips OccuSwitch Wireless Wall Switch, consider the following common troubleshooting steps:

• No Power to Load:
  • Check the circuit breaker to ensure power is on.
  • Verify all wiring connections are secure and correct, especially the Line, Load, and Neutral wires.
  • Ensure the switch is fully pressed to the ON position.
• Wireless Control Not Responding:
  • Confirm that the wireless sensor is powered and functioning correctly.
  • Ensure the switch is properly paired with the compatible wireless sensor according to the sensor's instructions.
  • Check for any obstructions or sources of interference that might affect wireless communication.
• Switch Feels Loose:
  • Turn off power at the circuit breaker.
  • Remove the wall plate and gently tighten the mounting screws that secure the switch to the electrical box.

If problems persist after attempting these steps, contact customer support or a qualified electrician.

8. Specifications

9. Warranty and Support

For warranty information and customer support, please refer to the documentation included with your product or visit the official Philips website. You may also contact Philips customer support directly for assistance with product inquiries, technical support, or warranty claims.

Customer Support Contact: 1-800-372-3331 (as indicated on product label).